Aggiusta la tua roba Comunità Store

GameSir X2 Type-C USB-C Port Replacement

Introduzione

The USB-C Plug connects the mobile phone to the GameSir X2 Type-C and is the only source of connection from the mobile phone to the controller. GameSir designed the USB-C plug to pivot 51 degrees to prevent damage to mobile phone charging ports while inserting and removing the device.

If your phone fails to connect to the Gamesir X2 Type-C, the USB-C plug may need replaced. Follow this guide to replace the plug. Before replacing the plug, review the troubleshooting page. More than likely a bad connection can be fixed without replacing the USB-C plug.

Cosa ti serve

  1. GameSir X2 Type-C USB-C Port Replacement, Back Cover: passo 1, immagine 1 di 2 GameSir X2 Type-C USB-C Port Replacement, Back Cover: passo 1, immagine 2 di 2

    • Turn the device so the back faces you.

    Traduci

  2. GameSir X2 Type-C USB-C Port Replacement: passo 2, immagine 1 di 2 GameSir X2 Type-C USB-C Port Replacement: passo 2, immagine 2 di 2

    • Remove the eight 6 mm T6 Torx screws.

    Traduci

  3. GameSir X2 Type-C USB-C Port Replacement: passo 3, immagine 1 di 1

    • Use a straight edge to remove the rubber pad on the front of the device.

    Traduci

  5. GameSir X2 Type-C USB-C Port Replacement: passo 4, immagine 1 di 2 GameSir X2 Type-C USB-C Port Replacement: passo 4, immagine 2 di 2

    • Remove the four 4.5 mm screws with a Phillips #000 screwdriver.

    Traduci

  6. GameSir X2 Type-C USB-C Port Replacement: passo 5, immagine 1 di 2 GameSir X2 Type-C USB-C Port Replacement: passo 5, immagine 2 di 2

    • Use a straight edge to pry open the controller, following the seam on the controller.

    • Some force is necessary, but be careful not to damage any of the clips holding the controller together.

    Traduci

  7. GameSir X2 Type-C USB-C Port Replacement, USB-C Port: passo 6, immagine 1 di 2 GameSir X2 Type-C USB-C Port Replacement, USB-C Port: passo 6, immagine 2 di 2

    • Remove the two 6mm Phillips head screws.

    Traduci

  8. GameSir X2 Type-C USB-C Port Replacement: passo 7, immagine 1 di 2 GameSir X2 Type-C USB-C Port Replacement: passo 7, immagine 2 di 2

    • Gently remove the plastic bracket from the plug.

    Traduci

  9. GameSir X2 Type-C USB-C Port Replacement: passo 8, immagine 1 di 3 GameSir X2 Type-C USB-C Port Replacement: passo 8, immagine 2 di 3 GameSir X2 Type-C USB-C Port Replacement: passo 8, immagine 3 di 3

    • Identify where the ribbon wire connects to to the motherboard.

    • Flip the black locking ZIF flap holding the ribbon wire in place to the upward position.

    • Gently remove the ribbon cable away from the motherboard socket.

    Traduci

  10. GameSir X2 Type-C USB-C Port Replacement: passo 9, immagine 1 di 3 GameSir X2 Type-C USB-C Port Replacement: passo 9, immagine 2 di 3 GameSir X2 Type-C USB-C Port Replacement: passo 9, immagine 3 di 3

    • Once the cover is off of the plug and the ribbon wire is released from the flap, gently pull the USB-C plug away from the device.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 10

Ultimi 7 Giorni: 22

Ultimi 30 Giorni: 95

Tutti i Tempi: 116