Aggiusta la tua roba Comunità Store

Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement

Introduzione

Follow this guide to replace the eccentric arms on a 2018 Classen Sod Cutter model HSC18AHD.

Cosa ti serve

  1. Attenzione: i passaggi 1-4 provengono da una guida contrassegnata come in corso.

    Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement, Safety precautions: passo 1, immagine 1 di 2 Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement, Safety precautions: passo 1, immagine 2 di 2

    • Make sure the engine is off and cool to the touch before you proceed.

    Modifica

  2. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: passo 2, immagine 1 di 1

    • Place wheel chocks against the roller and rear wheel to prevent the machine from moving.

    Modifica

  3. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: passo 3, immagine 1 di 2 Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: passo 3, immagine 2 di 2

    • Flip the gas shutoff switch next to the motor to the left into the off position.

    Modifica

  4. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: passo 4, immagine 1 di 2 Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: passo 4, immagine 2 di 2

    • Grab the plastic housing at the end of the spark plug wire.

    • Pull firmly to disconnect the wire from the spark plug.

    Modifica

  6. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement, Remove the eccentric arms: passo 5, immagine 1 di 1

    • Use a 3/4 inch socket to remove the two bolts on the eccentric arm.

    • You may need to use a 3/4 inch wrench in combination with the socket wrench to hold the nuts in place.

    • During reassembly, apply threadlocker to the bolt securing the eccentric arm to the blade arm.

    Modifica

  7. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: passo 6, immagine 1 di 2 Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: passo 6, immagine 2 di 2

    • Remove the plastic washer from between the eccentric arm and the blade arm.

    Modifica

  8. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: passo 7, immagine 1 di 1

    • Lift the eccentric arm away from the blade arm.

    Modifica

  9. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: passo 8, immagine 1 di 2 Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: passo 8, immagine 2 di 2

    • Remove the steel washer from the eccentric shaft.

    Modifica

  10. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: passo 9, immagine 1 di 1

    • Remove the plastic washer from the eccentric shaft.

    Modifica

  11. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: passo 10, immagine 1 di 2 Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: passo 10, immagine 2 di 2

    • Remove the eccentric arm and plastic washer from the eccentric shaft.

    • Repeat steps 5–10 for the other eccentric arm.

    • During reassembly, use a grease gun to add grease to the bearings through the two Zerk fittings on each eccentric arm.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 3 persone hanno completato questa guida.

Autore

con 1 altro collaboratore

Sam Omiotek

Membro da: 02/25/19

75.409 Reputazione

288 Guide realizzate

Distintivi: 35

+32 altri distintivi

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 8

Ultimi 30 Giorni: 54

Tutti i Tempi: 1,610