Aggiusta la tua roba Diritto alla Riparazione Store

Casio CTK-501 Battery Connection Replacement

Scritto Da: Jimmy Winne (e 3 altri collaboratori)
  • Commenti: 1
  • Preferiti: 2
  • Completamenti: 2

Difficoltà

Moderato

Passi

9

Tempo Necessario

Suggerisci un tempo??

Sezioni

2

Contrassegni

3

Missed a Step

Passo Mancante

Oops! A questa guida al momento mancano alcuni passi importanti.

Confusing Text

Testo Confuso

Parte del testo di questa guida è confusionario, doppio, o fuori tema. Modificarlo per renderlo più chiaro!

Better Introduction

Introduzione Migliore

Migliora questa guida completando o revisionando la sua introduzione.

Strumenti

Acquista questi strumenti

Parti

Nessuna parte specificata.

  1. Flip the keyboard upside down so the bottom is angled towards you.

    • Flip the keyboard upside down so the bottom is angled towards you.

    Traduci

  2. Use a #2 Phillips screwdriver to remove the twenty-seven 12 mm screws from the dark gray bottom panel.

    • Use a #2 Phillips screwdriver to remove the twenty-seven 12 mm screws from the dark gray bottom panel.

    Traduci

  3. Remove the bottom panel by lifting the bottom panel up and outward from yourself.

    • Remove the bottom panel by lifting the bottom panel up and outward from yourself.

    Traduci

  5. Flip the entire keyboard so the keys face up, and be careful not to let the bottom drop. Flip the top half of the keyboard and set onto the bottom half with the internal parts facing up.

    • Flip the entire keyboard so the keys face up, and be careful not to let the bottom drop.

    • Flip the top half of the keyboard and set onto the bottom half with the internal parts facing up.

    Traduci

  6. Plug in the soldering iron and set it somewhere safe where it can't catch anything on fire.

    • Plug in the soldering iron and set it somewhere safe where it can't catch anything on fire.

    • Unscrew the top green circuit board with black and red wires running into it.

    Traduci

  7. Set the circuit board somewhere flat so it is safe to solder.

    • Set the circuit board somewhere flat so it is safe to solder.

    Traduci

  8. Heat up the solder covering the end of the wires connected to the circuit board. Once the solder melts, remove the wires from the circuit board.

    • Heat up the solder covering the end of the wires connected to the circuit board. Once the solder melts, remove the wires from the circuit board.

    Traduci

  9. Melt new solder with your soldering iron, then apply it over the tip of the wire touching the circuit board.

    • Melt new solder with your soldering iron, then apply it over the tip of the wire touching the circuit board.

    Traduci

  10. Once the wires are firmly attached screw the circuit board back onto the keyboard.

    • Once the wires are firmly attached screw the circuit board back onto the keyboard.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Autore

con 3 altri collaboratori

Jimmy Winne

Membro da: 04/10/2012

494 Reputazione

6 Guide realizzate

Distintivi: 13

+10 altri distintivi

Team

Cal Poly, Team 9-16, Amido Fall 2012 Membro di Cal Poly, Team 9-16, Amido Fall 2012

CPSU-AMIDO-F12S9G16

4 Membri

6 Guide realizzate

0 Commenti

Aggiungi un commento

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 28

Tutti i Tempi: 3,618