Aggiusta la tua roba Comunità Store

Canon Selphy CP910 Printer Body Replacement

Introduzione

The Canon Selphy CP910 is used to print pictures from a camera and WiFi connection. If there are any issues with the body of the printer, it may be necessary to remove it. For information regarding troubleshooting issues with the Canon Selphy CP910, go to Canon Selphy CP910 Troubleshooting.

Contact the manufacturer for inquiries about receiving parts of the Canon Selphy CP910.

Cosa ti serve

  1. Canon Selphy CP910 Printer Body Replacement, Disassembling Canon Selphy CP910 Body: passo 1, immagine 1 di 2 Canon Selphy CP910 Printer Body Replacement, Disassembling Canon Selphy CP910 Body: passo 1, immagine 2 di 2

    • Turn the printer over.

    • Use the PH1 screw bit to remove the three 8 mm screws in the middle of the back plate.

    • Keep track of these screws because you will need them to reassemble the printer.

    Modifica

  2. Canon Selphy CP910 Printer Body Replacement: passo 2, immagine 1 di 3 Canon Selphy CP910 Printer Body Replacement: passo 2, immagine 2 di 3 Canon Selphy CP910 Printer Body Replacement: passo 2, immagine 3 di 3

    • Loosen up the four 10 mm corner screws.

    • A screwdriver with a long shaft approximately 7mm in diameter will make it easier to reach these screws.

    Modifica

  3. Canon Selphy CP910 Printer Body Replacement: passo 3, immagine 1 di 3 Canon Selphy CP910 Printer Body Replacement: passo 3, immagine 2 di 3 Canon Selphy CP910 Printer Body Replacement: passo 3, immagine 3 di 3

    • Turn the device around and remove the "open" lid.

    • This lid needs to be removed in order to take the printer apart.

    • Gently bend the lid and remove it from its hinges.

    Modifica

  4. Canon Selphy CP910 Printer Body Replacement: passo 4, immagine 1 di 3 Canon Selphy CP910 Printer Body Replacement: passo 4, immagine 2 di 3 Canon Selphy CP910 Printer Body Replacement: passo 4, immagine 3 di 3

    • Turn the device back over and lift the top panel up.

    • Disconnect the ribbon cables leading to the LCD screen.

    • Pull the top panel off.

    Modifica

  6. Canon Selphy CP910 Printer Body Replacement, Printer Body: passo 5, immagine 1 di 2 Canon Selphy CP910 Printer Body Replacement, Printer Body: passo 5, immagine 2 di 2

    • Use the PH1 screw driver to remove the three screws on the motherboard.

    Modifica

  7. Canon Selphy CP910 Printer Body Replacement: passo 6, immagine 1 di 2 Canon Selphy CP910 Printer Body Replacement: passo 6, immagine 2 di 2

    • Remove the printer.

    • This will prevent the printer from falling out during repair.

    Modifica

  8. Canon Selphy CP910 Printer Body Replacement: passo 7, immagine 1 di 3 Canon Selphy CP910 Printer Body Replacement: passo 7, immagine 2 di 3 Canon Selphy CP910 Printer Body Replacement: passo 7, immagine 3 di 3

    • Remove the output connections.

    • Be careful! Do not pull too hard because the wires might rip.

    • Output connections are located on the corners of the motherboard.

    Modifica

  9. Canon Selphy CP910 Printer Body Replacement: passo 8, immagine 1 di 2 Canon Selphy CP910 Printer Body Replacement: passo 8, immagine 2 di 2

    • The motherboard is attached to three more ribbon wires.

    • Detach these wires.

    • Be careful not to pull too hard.

    Modifica

  10. Canon Selphy CP910 Printer Body Replacement: passo 9, immagine 1 di 2 Canon Selphy CP910 Printer Body Replacement: passo 9, immagine 2 di 2

    • Separate the motherboard from the main hard drive.

    Modifica

  11. Canon Selphy CP910 Printer Body Replacement: passo 10, immagine 1 di 3 Canon Selphy CP910 Printer Body Replacement: passo 10, immagine 2 di 3 Canon Selphy CP910 Printer Body Replacement: passo 10, immagine 3 di 3

    • Remove the main hard drive from the printer body.

    Modifica

  12. Canon Selphy CP910 Printer Body Replacement: passo 11, immagine 1 di 2 Canon Selphy CP910 Printer Body Replacement: passo 11, immagine 2 di 2

    • Gently remove the fan from the body.

    • The fan is glued to the case. When you install it in the new body, use hot glue to secure it in place.

    Modifica

  13. Canon Selphy CP910 Printer Body Replacement: passo 12, immagine 1 di 2 Canon Selphy CP910 Printer Body Replacement: passo 12, immagine 2 di 2

    • The empty case will look like this once all the parts are removed.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Autore

con 6 altri collaboratori

Christie Peralta

Membro da: 02/01/16

700 Reputazione

5 Guide realizzate

Distintivi: 15

+12 altri distintivi

Team

UW Tacoma, Team 1-6, Rose Winter 2016 Membro di UW Tacoma, Team 1-6, Rose Winter 2016

UWT-ROSE-W16S1G6

4 Membri

10 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 11

Ultimi 30 Giorni: 47

Tutti i Tempi: 4,217