Canon EOS Rebel T2i Tripod Mount Replacement

Introduzione

This guide shows you how to replace the tripod socket plate. This can be useful if the threads on the tripod mount gets damaged to where it is no longer useable.

The Phillips #000 screwdriver is marked as an optional tool as you can always use the JIS #000 screwdriver in its place (JIS screwdrivers won't damage Phillips head screws).

Cosa ti serve

Passo 1 I/F Terminal Cover

Canon EOS Rebel T2i Tripod Mount Replacement, I/F Terminal Cover: passo 1, immagine 1 di 3

Canon EOS Rebel T2i Tripod Mount Replacement, I/F Terminal Cover: passo 1, immagine 2 di 3

Canon EOS Rebel T2i Tripod Mount Replacement, I/F Terminal Cover: passo 1, immagine 3 di 3

Before beginning, ensure that the camera is off, and the battery is removed.
Pry open the rubber I/F terminal cap with your finger.
Remove the two M1.7x2.5mm JIS #000 screws that are underneath the I/F terminal cap.
Using a plastic pick, or another thin plastic prying tool, pop off the I/F terminal cover from the camera.

Modifica

Passo 2 Remove the back casing.

Canon EOS Rebel T2i Tripod Mount Replacement, Remove the back casing.: passo 2, immagine 1 di 2

Canon EOS Rebel T2i Tripod Mount Replacement, Remove the back casing.: passo 2, immagine 2 di 2

On the left side of the camera, remove the following screw:
One M1.7x6.0mm JIS #000 screw
On the right side, remove the following screws:
One M1.7x5.5mm JIS #000 screw
One M1.7x3.5mm JIS #000 screw

Modifica

Passo 3

Remove the battery door.
Open the battery door to about a 35° angle.
Pull the battery door straight outwards.
Remove the following screws from the bottom of the camera:
One M1.7x6.0mm JIS #000 screw
Two M1.7x2.5mm JIS #000 screws
One M1.7x5.5mm JIS #000 screw

Modifica

Passo 4 Open the back panel.

Canon EOS Rebel T2i Tripod Mount Replacement, Open the back panel.: passo 4, immagine 1 di 3

Canon EOS Rebel T2i Tripod Mount Replacement, Open the back panel.: passo 4, immagine 2 di 3

Canon EOS Rebel T2i Tripod Mount Replacement, Open the back panel.: passo 4, immagine 3 di 3

Slide the viewfinder eyepiece vertically upwards.
Start to pull the back cover partially off of the camera.
Use caution when removing the back cover, there is a ribbon cable that connects the LCD screen to the main PCB board.
Disconnect the LCD screen ribbon cable from the main PCB board.
Use a plastic spudger to lift up the black locking tab.
Carefully pull out the ribbon cable from its connector using a pair of angled tweezers.
Finish pulling the back cover off of the camera body.

Modifica

Passo 5 Front Cover

Canon EOS Rebel T2i Tripod Mount Replacement, Front Cover: passo 5, immagine 1 di 2

Canon EOS Rebel T2i Tripod Mount Replacement, Front Cover: passo 5, immagine 2 di 2

Remove the following screws from the front of the camera:
Two M1.7x5.5mm JIS #000 screws
On the bottom of the camera, remove the following screws:
Three M1.7x5.5mm JIS #000 screws

Modifica

Passo 6

Canon EOS Rebel T2i Tripod Mount Replacement: passo 6, immagine 3 di 3

Slide a spudger tool towards the tripod mount, underneath the plastic cover.
Push the plastic cover up and over the tripod mount.
Pull the front cover off of the camera.
Electric Shock Warning: With the front cover off, the high voltage capacitor on the DC PCB board is now exposed. It is recommended that you use a capacitor discharge tool to ensure the capacitor is fully discharged before proceeding further.