Aggiusta la tua roba Comunità Store

Braven BRV-X Button Module(s) Replacement

Introduzione

If the buttons on your speaker are not working, they may need to be replaced. Use this guide to replace the button module on your Braven BRV-X.

Cosa ti serve

  1. Braven BRV-X Button Module(s) Replacement, Front Speaker Panel: passo 1, immagine 1 di 1

    • Remove four 1.1 cm outer screws in the outer shell using the Phillips #00 screwdriver.

    Modifica

  2. Braven BRV-X Button Module(s) Replacement: passo 2, immagine 1 di 1

    • Remove four 1.3 cm inner screws in the outer shell using the 1.5mm Hex screwdriver.

    Modifica

  3. Braven BRV-X Button Module(s) Replacement: passo 3, immagine 1 di 1

    • Gently remove the outer shell.

    Modifica

  4. Braven BRV-X Button Module(s) Replacement: passo 4, immagine 1 di 2 Braven BRV-X Button Module(s) Replacement: passo 4, immagine 2 di 2

    • Cut adhesive tape on both sides.

    Modifica

  5. Braven BRV-X Button Module(s) Replacement: passo 5, immagine 1 di 2 Braven BRV-X Button Module(s) Replacement: passo 5, immagine 2 di 2

    • Remove eighteen 0.9cm screws in the inner shell using the Phillips #00 screwdriver.

    Modifica

  7. Braven BRV-X Button Module(s) Replacement: passo 6, immagine 1 di 3 Braven BRV-X Button Module(s) Replacement: passo 6, immagine 2 di 3 Braven BRV-X Button Module(s) Replacement: passo 6, immagine 3 di 3

    • Pry open the glued inner shell using a spudger around all sides of the shell.

    • Don't use too much pressure as that could cause damage to the plastic.

    Modifica

  8. Braven BRV-X Button Module(s) Replacement: passo 7, immagine 1 di 2 Braven BRV-X Button Module(s) Replacement: passo 7, immagine 2 di 2

    • Remove ten 0.7 cm screws in the front plate using the 1.5 mm Hex screwdriver.

    Modifica

  9. Braven BRV-X Button Module(s) Replacement: passo 8, immagine 1 di 2 Braven BRV-X Button Module(s) Replacement: passo 8, immagine 2 di 2

    • Use a spudger to open the front speaker plate.

    Modifica

  10. Braven BRV-X Button Module(s) Replacement: passo 9, immagine 1 di 1

    • Remove three 1.0 cm screws from the battery unit.

    • It is recommended (but not required) to remove the battery.

    Modifica

  11. Braven BRV-X Button Module(s) Replacement: passo 10, immagine 1 di 2 Braven BRV-X Button Module(s) Replacement: passo 10, immagine 2 di 2

    • Disconnect the ribbon cable attached the main board.

    Modifica

  12. Braven BRV-X Button Module(s) Replacement: passo 11, immagine 1 di 3 Braven BRV-X Button Module(s) Replacement: passo 11, immagine 2 di 3 Braven BRV-X Button Module(s) Replacement: passo 11, immagine 3 di 3

    • Pry open the second plate holding in the speaker using a spudger around all sides.

    • It is recommended to use a spudger to remove the heavily glued areas between the plates before prying.

    • Don't use too much pressure as that could cause damage to the plastic.

    Modifica

  13. Braven BRV-X Button Module(s) Replacement: passo 12, immagine 1 di 3 Braven BRV-X Button Module(s) Replacement: passo 12, immagine 2 di 3 Braven BRV-X Button Module(s) Replacement: passo 12, immagine 3 di 3

    • Cut the 20 gauge wires attached to the front IR sensor and two speaker wires.

    • Leave enough length on the wire to work with it afterwards.

    • Cut the 22 gauge wire attached in the corner.

    • Solder the new speaker plate during reassembly.

    • To properly solder and desolder connections, visit the How to Solder and Desolder Connections guide.

    Modifica

  14. Braven BRV-X Button Module(s) Replacement, Button Module(s): passo 13, immagine 1 di 2 Braven BRV-X Button Module(s) Replacement, Button Module(s): passo 13, immagine 2 di 2

    • Remove the ribbon cable attached to the main board.

    • Pull from the clip and not from the cable.

    Modifica

  15. Braven BRV-X Button Module(s) Replacement: passo 14, immagine 1 di 1

    • Remove three 0.7 cm screws from the button module(s) using the Phillips #00 screwdriver.

    Modifica

  16. Braven BRV-X Button Module(s) Replacement: passo 15, immagine 1 di 1

    • Gently lift the button module from the enclosure.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 1 altro collaboratore

Trey Peterson

Membro da: 04/01/19

301 Reputazione

2 Guide realizzate

Distintivi: 3

Team

IUPUI, Team S1-G5, Harley Spring 2019 Membro di IUPUI, Team S1-G5, Harley Spring 2019

IUPUI-HARLEY-S19S1G5

3 Membri

2 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 5

Ultimi 30 Giorni: 13

Tutti i Tempi: 386