Aggiusta la tua roba Comunità Store

Autosampler Configuration (For Old & New Versions)

Cosa ti serve

  1. Autosampler Configuration (For Old & New Versions), Starting the configuration process.: passo 1, immagine 1 di 2 Autosampler Configuration (For Old & New Versions), Starting the configuration process.: passo 1, immagine 2 di 2

    • 1. Turn on the autosampler. Screen will read "...STANDBY..."

    • 2. Press "ENTER/PROGRAM" button. Use arrows to highlight "CONFIGURE". Press "ENTER/PROGRAM" button

    • This will allow you to use the arrows to shuffle through the different configuration options. To select the one you want, press the "ENTER/PROGRAM" button.

    Traduci

  2. Autosampler Configuration (For Old & New Versions), Configuring "set clock".: passo 2, immagine 1 di 1

    • The first option for configuring is "SET CLOCK"

    • 3. Press "ENTER/PROGRAM" to "SET CLOCK". Use the numeric keys to set the time and date. You can use the arrows to move. When finished. Press "ENTER/PROGRAM" button.

    Traduci

  3. Autosampler Configuration (For Old & New Versions), Configuring "bottles and sizes".: passo 3, immagine 1 di 1

    • 4. Press "ENTER/PROGRAM" to configure "BOTTLES AND SIZES".

    • Use arrows to select "PORTABLE" sampler. Press "ENTER/PROGRAM" to configure bottles and sizes.

    • Use arrows to select "24" botles. Press "ENTER/PROGRAM" button.

    • Use numeric keys to enter "1000" mL for the "BOTTLE VOLUME". Press "ENTER/PROGRAM" button.

    Traduci

  4. Autosampler Configuration (For Old & New Versions), Configuring "suction line".: passo 4, immagine 1 di 1

    • 5. Press "ENTER/PROGRAM" to configure "SUCTION LINE".

    • Use arrow to select "3/8" inch for "SUCTION LINE I.D." Press "ENTER/PROGRAM" button.

    • Use arrow to select "VINYL" for "SUCTION LINE" type. Press "ENTER/PROGRAM" button.

    • Use numeric keys to enter "25" feet for "SUCTION LINE LENGTH". Press "ENTER/PROGRAM" button.

    • The suction line length may change based on location and should be measured!

    Traduci

  5. Autosampler Configuration (For Old & New Versions), Configuring "liquid detector".: passo 5, immagine 1 di 1

    • 6. Press "ENTER/PROGRAM" button to configure "LIQUID DETECTOR".

    • Use arrows to select "ENABLE" "LIQUID DECTOR". Press "ENTER/PROGRAM" button.

    • Use numeric keys to enter "3" "RINSE CYCLES." Press "ENTER/PROGRAM" button.

    • Screen will read "ENTER HEAD MANUALLY?" Use arrows to select "NO". Press "ENTER/PROGRAM" button.

    • Screen will read "RETRY UP TO X TIMES WHEN SAMPLING?" Use numeric keys to enter "3". Press "ENTER/PROGRAM" button.

    Traduci

  7. Autosampler Configuration (For Old & New Versions), Configuring "programming mode".: passo 6, immagine 1 di 1

    • 7. Press "ENTER/PROGRAM" to configure "PROGRAMMING MODE".

    • Use arrows to select "BASIC" mode. Press "ENTER/PROGRAM" button.

    Traduci

  8. Autosampler Configuration (For Old & New Versions), Configuring "calibrate sampler".: passo 7, immagine 1 di 1

    • 8. Press "ENTER/PROGRAM" to configure "CALIBRATE SAMPLER".

    • Use arrows to select "DISABLE" "CALIBRATE SAMPLER". Press "ENTER/PROGRAM" button.

    Traduci

  9. Autosampler Configuration (For Old & New Versions), Configuring "start time delay".: passo 8, immagine 1 di 1

    • 9. Press "ENTER/PROGRAM" to configure "START TIME DELAY". Press "ENTER/PROGRAM" button.

    • Screen will read "X MINUTE DELAY TO START." Use numeric keys to enter "0" minutes. Press "ENTER/PROGRAM" button.

    Traduci

  10. Autosampler Configuration (For Old & New Versions), Configuring "enabling pin".: passo 9, immagine 1 di 1

    • 10. Press "ENTER/PROGRAM" to configure "ENABLE PIN". Press "ENTER/PROGRAM" button.

    • Use arrow to select "NO" for "MASTER/SLAVE MODE?" Press "ENTER/PROGRAM" button.

    • Use arrow to select "NO" for "SAMPLE UPON DISABLE?" Press "ENTER/PROGRAM" button.

    • Use arrow to select "NO" for "SAMPLE UPON ENABLE?" Press "ENTER/PROGRAM" button.

    • Use arrow to select "NO" for "RESET SAMPLE INTERVAL?" Press "ENTER/PROGRAM" button.

    • Use arrow to select "NO" for "INHIBIT COUNTDOWN?" Press "ENTER/PROGRAM" button.

    Traduci

  11. Autosampler Configuration (For Old & New Versions), Configuring "event mark".: passo 10, immagine 1 di 1

    • 11. Press "ENTER/PROGRAM" to configure "EVENT MARK". Press "ENTER/PROGRAM" button.

    • Use arrow to select "CONTINUOUS SIGNAL". Press "ENTER/PROGRAM" button.

    • Use arrow to select "PUMP CYCLE". Press "ENTER/PROGRAM" button.

    • It is critical this setting is configured in order for the sensor node to operate the autosampler!

    Traduci

  12. Autosampler Configuration (For Old & New Versions), Configuring "purge counts".: passo 11, immagine 1 di 1

    • 12. Press "ENTER/PROGRAM" to configure "PURGE COUNTS". Press "ENTER/PROGRAM" button.

    • Use numeric keys to enter "XX" for "PRE-SAMPLE COUNTS". Press "ENTER/PROGRAM" button.

    • Use numeric keys to enter "XX" for "POST-SAMPLE COUNTS". Press "ENTER/PROGRAM" button.

    Traduci

  13. Autosampler Configuration (For Old & New Versions), Configuring "tubing life".: passo 12, immagine 1 di 1

    • 12. Press "ENTER/PROGRAM" to configure "TUBING LIFE". Press "ENTER/PROGRAM" button.

    • Screen will read "X PUMP COUNTS, WARNING AT XXX000". Press "ENTER/PROGRAM" button.

    • Use arrows to select "NO" for "RESET PUMP COUNTER?". Press "ENTER/PROGRAM" button.

    • Use numeric keys to enter "XXX000" for "PUMP COUNTS TO WARNING". Press "ENTER/PROGRAM" button.

    Traduci

  14. Autosampler Configuration (For Old & New Versions), Configuring "program lock".: passo 13, immagine 1 di 1

    • 13. Press "ENTER/PROGRAM" to configure "PROGRAM LOCK". Press "ENTER/PROGRAM" button.

    • Use arrows to select "DISABLE" "PROGRAM LOCK". Press "ENTER/PROGRAM" button.

    Traduci

  15. Autosampler Configuration (For Old & New Versions), Configuring "sampler ID".: passo 14, immagine 1 di 1

    • 15. The next configuration option is "SAMPLER ID". Skip this configuration step by using the arrows.

    Traduci

  16. Autosampler Configuration (For Old & New Versions), Configuring "run diagonostics".: passo 15, immagine 1 di 1

    • 16. The next configuration option is "RUN DIAGNOSTICS". Skip this configuration step by using the arrows.

    Traduci
Linea Traguardo

Altre 2 persone hanno completato questa guida.

Autore

con 1 altro collaboratore

Brooke Mason

Membro da: 05/29/19

2.928 Reputazione

17 Guide realizzate

Distintivi: 21

+18 altri distintivi

Team

Open-Storm Membro di Open-Storm

Community

14 Membri

24 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 1

Tutti i Tempi: 171