Aggiusta la tua roba Comunità Store

Apple Lisa MacWorks II PFG Instalation

Cosa ti serve

  1. Apple Lisa MacWorks II PFG Instalation, Disassembly: passo 1, immagine 1 di 2 Apple Lisa MacWorks II PFG Instalation, Disassembly: passo 1, immagine 2 di 2
    Modifica

  2. Apple Lisa MacWorks II PFG Instalation, Remove I/O Board: passo 2, immagine 1 di 2 Apple Lisa MacWorks II PFG Instalation, Remove I/O Board: passo 2, immagine 2 di 2

    • Remove the Lisa's I/O Board. The I/O Board's clips are marked in red.

    • Release both clips holding the I/O Board.

    • Pull the I/O Board up to remove it.

    Modifica

  3. Apple Lisa MacWorks II PFG Instalation, Removing the 8530 Chip: passo 3, immagine 1 di 1

    • Remove the chip marked 8530 at location 9D.

    Modifica

  5. Apple Lisa MacWorks II PFG Instalation, Crystal Insulation: passo 4, immagine 1 di 1

    • Next to the chip removed in step 3 is a crystal. These are not always installed with a plastic coating. The crystal shown in the image is insulated.

    • If your crystal is not insulated then tape a small piece of cardboard on top of it.

    Modifica

  6. Apple Lisa MacWorks II PFG Instalation, Installing the Daughter Board: passo 5, immagine 1 di 1

    • Ensure the pins on the MW+II PFG (Programable Frequency Generator) are perfectly straight. If they are not then slightly bend them into place.

    • Insert the PFG into the 8530 socket.

    Modifica

  7. Apple Lisa MacWorks II PFG Instalation, Attaching Red and Black Wires: passo 6, immagine 1 di 3 Apple Lisa MacWorks II PFG Instalation, Attaching Red and Black Wires: passo 6, immagine 2 di 3 Apple Lisa MacWorks II PFG Instalation, Attaching Red and Black Wires: passo 6, immagine 3 di 3

    • Locate the chip marked LS132 located at 6A.

    • Connect the Red and Black wires as shown in the second image on this step.

    • It is best to place a piece of electrical tape on the wires to help hold them in place.

    Modifica

  8. Apple Lisa MacWorks II PFG Instalation: passo 7, immagine 1 di 1

    • Replace the I/O Board back into Lisa's Card Cage.

    • Replace Lisa's Card Cage Back into the Lisa.

    • Replace the rear panel on the Lisa.

    • MacWorks + II (MW+II) floppy images can be found here.

    • The MW+II manual can be found here which includes detailed instructions how to instal thel MW+II software.

    Modifica
Conclusione
  • MW+II supports Macintosh System Software up to Macintosh System 7.5.5.
  • Supports over 10MB of RAM (more than 4MB requires an XLerator.)

Un'altra persona ha completato questa guida.

Documenti Allegati

Autore

con 1 altro collaboratore

LisaGuide

Membro da: 12/30/18

1.833 Reputazione

11 Guide realizzate

Distintivi: 9

+6 altri distintivi

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 4

Ultimi 30 Giorni: 8

Tutti i Tempi: 582