Domande
-
When iPhones battery drains to nothing, I cannot charge itAfter disassembling my iPhone, i noticed that if the battery drains all the way out and it shuts off because of it, and then ...
-
screen raised, off center, logic board tilted, not snapped in.I took apart my iPhone 3G and after putting it back together the screen assembly is uneven and will not snap in properly. The...
Risposte
-
Rispondi a: Black Display After RepairThis is what i would suggest. Take it apart, down to removing the logic board. Sometimes when you recontact the logic board and the battery it seems to work. I wouldnt advise it but you could just remove the four screws on the right side of the logic board and then tilt it off the battery connector leads in order to recontact the logic board. I wouldn't advise it because you could bend or snap your board, but this is the way i did it. Sometimes its not the front assembly ribbons but the other ribbons or the contact between the board and battery. If that does not work let me know and i will suggest another way.
-
Rispondi a: bottom half of my iPhone won't workIf you mean it wont work because it does not respond to touch, it is most likely the digitizer. Depending on if you still have your 1 year warranty through apple active depends on how you should proceed. If you do still have it active, bring it to apple, and they should replace it for free (if there is no sign of damage). If you do not have your 1 year warranty active still, you should check ribbon 2 to make sure it is fully connected. If ribbons 1, 2, and 3 are all connected properly and it still does not work you will need to purchase a new digitizer.
-
Rispondi a: Can't charge or SyncFirst start off my making sure ribbon number 4 is fully connected. If that doesnt work you may need to restore your iPhone. Could you even do this due to the fact that you cannot sync with itunes?
-
Rispondi a: Why wont the home button work?Be sure that all the ribbons are connected fully, generally its number 2 or 3 thats the problem. If that doesnt work let me know and i will suggest another way.
-
Rispondi a: Why don't my internal Mic and speaker don't work anymore?Make sure ribbon number 4 is connected. Disconnect and then reconnect. You can look in the tutorials to see where number 4 is if you dont know or if its not labeled.
-
Rispondi a: Replaced front panel, last 2 screws left then screen when black!This is what i would suggest. Take it apart, down to removing the logic board. Sometimes when you recontact the logic board and the battery it seems to work. I wouldnt advise it but you could just remove the four screws on the right side of the logic board and then tilt it off the battery connector leads in order to recontact the logic board. I wouldn't advise it because you could bend or snap your board, but this is the way i did it. Sometimes its not the front assembly ribbons but the other ribbons or the contact between the board and battery. If that does not work let me know and i will suggest another way.
Ore di Attività
L'orario del giorno in cui sei stato attivo negli ultimi 90 giorni. Ogni linea di questo grafico è un'azione che hai eseguito sul sito (contano solo azioni rilevanti, come votare o modificare post). I numeri alla base del grafico sono l'orario del giorno in Mountain Standard Time.
-78
La risposta a "Error 23 When restoring. Brick or no?" è stata contrassegnata come inappropriata ed eliminata.
@
+12
+12
+12
Reputazione nel tempo
Dettaglio Reputazione
| Evento | Conteggio | Delta |
|---|---|---|
| Il post ha ricevuto un voto positivo | 6 | 72 |
| Risposta accettata | 2 | 60 |
| Il post ha ricevuto un voto negativo | 1 | -6 |
| Eliminato il tuo post a seguito di segnalazioni | 1 | -78 |
Distintivi
181758
Notifiche Recenti
Segna tutti come già letti
Show:
Tutto
Tutto
Non letto