Strumenti necessari in questo Smontaggio

Introduzione

My first Handheld Device. A Sony FM/AM Tape Cassette Walkman. It has Digital Controls for the Radio /Alarm Clock on the front and Old school cassette controls on the side. Found it again in a Logitech Tape Case with a Live Medski, Martin and Wood show from 99 in it. Runs on 2 AA batteries. This Walkman was my first Portbale device and I've kept it through all these years. Tis officially my first breakdown on IFIXIT

Questo smontaggio non è una guida di riparazione. Per riparare il tuo Sony Walkman WM-FX20, usa il nostro manuale di assistenza.

Good Ole Sony Walkman.
  • Good Ole Sony Walkman.

Aggiungi Commento

Start with removing the screw on the Underside. The screw on the Backside next. Then the two on the reverse side of the tape controls. New line. New line.
  • Start with removing the screw on the Underside. The screw on the Backside next. Then the two on the reverse side of the tape controls.

  • New line.

Aggiungi Commento

With a small Phillips head, Pry the sides carefully. With a small Phillips head, Pry the sides carefully. With a small Phillips head, Pry the sides carefully.
  • With a small Phillips head, Pry the sides carefully.

Aggiungi Commento

Take care not to jostle the Switches on the top of the unit while removing case. So now we have removed the underside casing from the device. Take care not to jostle the Switches on the top of the unit while removing case. So now we have removed the underside casing from the device.
  • Take care not to jostle the Switches on the top of the unit while removing case. So now we have removed the underside casing from the device.

Aggiungi Commento

MacBook Battery Fix Kits
Fix Kits Starting at $69.99
MacBook Battery Fix Kits
Starting at $69.99
Find Ribbon Cable that connects to the board. Carefully Pry open either side of connector as shown, then remove ribbon cable from board. Find Ribbon Cable that connects to the board. Carefully Pry open either side of connector as shown, then remove ribbon cable from board. Find Ribbon Cable that connects to the board. Carefully Pry open either side of connector as shown, then remove ribbon cable from board.
  • Find Ribbon Cable that connects to the board. Carefully Pry open either side of connector as shown, then remove ribbon cable from board.

Aggiungi Commento

Now we can remove the board from the casing.
  • Now we can remove the board from the casing.

Aggiungi Commento

If you do not need to replace the front door control assembly I would not suggest to continue any further- That little spring took me a good 40 minutes to properly get back in place. It is Crucial to get it in right so that the Cassette door stays flush and closed. Find Door Spring and remove carefully. Then find and pry off (on either side) glued on bumpers- These limit the distance the door hinge can travel in order to be pulled off--- Find Door Spring and remove carefully. Then find and pry off (on either side) glued on bumpers- These limit the distance the door hinge can travel in order to be pulled off---
  • If you do not need to replace the front door control assembly I would not suggest to continue any further- That little spring took me a good 40 minutes to properly get back in place. It is Crucial to get it in right so that the Cassette door stays flush and closed.

  • Find Door Spring and remove carefully. Then find and pry off (on either side) glued on bumpers- These limit the distance the door hinge can travel in order to be pulled off---

Aggiungi Commento

Now gently pry the door hinges on either side off of their pivot point, and remove the front door from the assembly Now gently pry the door hinges on either side off of their pivot point, and remove the front door from the assembly
  • Now gently pry the door hinges on either side off of their pivot point, and remove the front door from the assembly

Aggiungi Commento

Remove three screws on backside of cassette door. Then remove panel. Remove three screws on backside of cassette door. Then remove panel. Remove three screws on backside of cassette door. Then remove panel.
  • Remove three screws on backside of cassette door. Then remove panel.

Aggiungi Commento

There is your front mounted control board!  It is attached to what appears to be a speaker i'm guessing. Possibly for the alarm clock.  I found that to be interesting, the little speaker thing.  Anyways , thats it. There is your front mounted control board!  It is attached to what appears to be a speaker i'm guessing. Possibly for the alarm clock.  I found that to be interesting, the little speaker thing.  Anyways , thats it. There is your front mounted control board!  It is attached to what appears to be a speaker i'm guessing. Possibly for the alarm clock.  I found that to be interesting, the little speaker thing.  Anyways , thats it.
  • There is your front mounted control board! It is attached to what appears to be a speaker i'm guessing. Possibly for the alarm clock. I found that to be interesting, the little speaker thing. Anyways , thats it.

Aggiungi Commento

JaosnT

Membro da: 12/10/2009

407 Reputazione

5 Guide realizzate

Please provide more info on how to put the spring back together again. I have a WM-FX435.

Robert Surya - Replica

Hi, the casette operation has failed. Now I try to check. Really I do not the reason. Any suggestion?

Batur Salamom - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 7

Ultimi 7 Giorni: 16

Ultimi 30 Giorni: 88

Tutti i Tempi: 19,013