Strumenti necessari in questo Smontaggio

Introduzione

A teardown of the Nikon Coolpix 3500.

Questo smontaggio non è una guida di riparazione. Per riparare il tuo Nikon Coolpix 3500, usa il nostro manuale di assistenza.

Open the battery cover.
  • Open the battery cover.

  • Remove the battery.

Aggiungi Commento

Remove two 4.5 mm screws next to the battery opening.
  • Remove two 4.5 mm screws next to the battery opening.

  • Remove one 3 mm screw above the CF Card opening.

  • Remove one 4.5 mm screw next to CF card opening.

Aggiungi Commento

Remove two 4.5 mm screws from inside the battery slot.
  • Remove two 4.5 mm screws from inside the battery slot.

Aggiungi Commento

Remove two 5 mm screws from the opposite end of the battery.
  • Remove two 5 mm screws from the opposite end of the battery.

Aggiungi Commento

Remove the plastic cap and  newly revealed 5 mm screw.
  • Remove the plastic cap and newly revealed 5 mm screw.

Aggiungi Commento

Remove the five identical 3.5 mm screws from the bottom of the camera.
  • Remove the five identical 3.5 mm screws from the bottom of the camera.

  • Remove the grey plastic piece by gently prying the faceplate up.

  • Note: Do not pull hard, there are two wires connecting the faceplate to the logic board.

Aggiungi Commento

Use the spudger to lift up the white-capped wire. Use a spudger to lift up the orange-capped wire at the bottom of the camera and set the faceplate aside. Use a spudger to lift up the orange-capped wire at the bottom of the camera and set the faceplate aside.
  • Use the spudger to lift up the white-capped wire.

  • Use a spudger to lift up the orange-capped wire at the bottom of the camera and set the faceplate aside.

Aggiungi Commento

Disconnect the grey-capped wire from the logic board.
  • Disconnect the grey-capped wire from the logic board.

  • Disconnect the blue wire attached to the green chip from the center of the logic board.

Aggiungi Commento

Remove the 3.5 mm screw from the logic board next to the rotating lens. Invert the logic board and lens toward the orange and blue wires still connecting the logic board to the LED screen.
  • Remove the 3.5 mm screw from the logic board next to the rotating lens.

  • Invert the logic board and lens toward the orange and blue wires still connecting the logic board to the LED screen.

Aggiungi Commento

Disconnect the blue wire connecting the logic board to the LED screen. Disconnect the orange wire using a spudger while pushing out horizontally.
  • Disconnect the blue wire connecting the logic board to the LED screen.

  • Disconnect the orange wire using a spudger while pushing out horizontally.

  • Disconnect the red capped wire from the logic board.

  • Lift the logic board and lens (still connected) out of the back case.

Aggiungi Commento

Lift up on the black covering and remove the orange wire connecting the lens to the logic board.
  • Lift up on the black covering and remove the orange wire connecting the lens to the logic board.

Aggiungi Commento

Remove the 2.5 mm screw.
  • Remove the 2.5 mm screw.

  • Remove the two 3.4 mm screws.

  • Remove the two 4.4 mm screws.

Aggiungi Commento

Remove the LED screen. Be careful not to let the three-button rubber piece fall out while removing it.
  • Remove the LED screen.

  • Be careful not to let the three-button rubber piece fall out while removing it.

Aggiungi Commento

richard guenther

Membro da: 19/04/2010

183 Reputazione

6 Guide realizzate

Team

Cal Poly, Team 30-38, Garner Spring 2010 Membro di Cal Poly, Team 30-38, Garner Spring 2010

CPSU-GARNER-S10S30G38

5 Membri

6 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 2

Tutti i Tempi: 7,372