Panoramica Video

Introduzione

Here is a video teardown of the ThinkPad T410s.

Below is a step by step teardown

Questo smontaggio non è una guida di riparazione. Per riparare il tuo Lenovo ThinkPad 410s, usa il nostro manuale di assistenza.

  • Unlatch and remove battery

Aggiungi Commento

  • Open Acess panel

Aggiungi Commento

  • Remove Hard drive

Aggiungi Commento

  • Remove wirless WAN

Aggiungi Commento

  • Remove DIMM from back

Aggiungi Commento

  • Remove Keyboard retaing Screw from bottom of system

  • Turn the system over and open the cover. Push the keyboard toward the back and lift it up. Slide it forward to rest it on the palm rest. Disconnect the ribbon cable.

Aggiungi Commento

  • Remove BIOS battery

Aggiungi Commento

  • Disconnect the two antenna leads from the Wireless WAN card. Remove the two retaining screws. Rotate the card up and pull it out of the slot.

  • Remeber which lead goes where Prior to removing it . Grey is usually MAIN , black AUX

Aggiungi Commento

  • Remove 14 retaining screws from back

  • The first 9 are required for bezel and touchpad removal .

  • M2 × 14 mm, wafer-head, nylon-coated (6)

  • M2 × 3 mm, wafer-head, nylon-coated (3)

  • The remaining need to be removed for base cover removal

  • M2 × 5 mm, wafer-head, nylon-coated (4)

  • M2 × 10 mm, wafer-head, nylon-coated (1)

  • Note: The FPC cable is attached on the underside of the keyboard bezel assembly. In some models, the Bluetooth daughter card is also attached on the underside of the keyboard bezel assembly.

Aggiungi Commento

  • Turn system over , open , remove 4 retaining screws and the work form one side , using spudger to remove chasis bezel

  • M2 × 3 mm, wafer-head, nylon-coated (4)

Aggiungi Commento

  • Remove 4 retaining screws

  • M2 × 3 mm, wafer-head, nylon-coated (4)

Aggiungi Commento

  • Remove the two retaining screws on the bottom of the system.

  • M2.5 × 6 mm, wafer-head, nylon-coated (2)

  • Turn the system over and open the cover.

  • Unroute all the wires.

  • Remove the retaining screws.

  • M2.5 × 6 mm, wafer-head, nylon-coated (2)

  • Carefully lift the LCD panel up and out of the chass

Aggiungi Commento

kevinleroy

Membro da: 13/08/2012

302 Reputazione

1 Guida realizzata

Team

Master Techs Membro di Master Techs

Community

274 Membri

712 Guide realizzate

Uhm, sorry, what about the photos? I don't see any...

JoeMuc2014 - Replica

Still not seeing any photos accompanying the steps listed in the teardown.

Jason Landers - Replica

well. if get short out inside of USB or network line>> that has been stopping the software lunched.

mohammed - Replica

we need teardown of T410

mohammed - Replica

The video shows a teardown of the T410s. It is a lot different from the T410.

Robert Oschmann - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 12

Ultimi 30 Giorni: 66

Tutti i Tempi: 6,135