Aggiusta la tua roba Comunità Store

Xbox 360 Wireless Controller Teardown

Scritto Da: Mart-Jan (e 7 altri collaboratori)
Pubblicato: June 1, 2019
  • Commenti: 5
  • Preferiti: 7
  • Visualizzazioni: 39,2k

Xbox 360 Wireless Controller Teardown

Scritto Da: Mart-Jan (e 7 altri collaboratori)
Pubblicato: June 1, 2019
  • Commenti: 5
  • Preferiti: 7
  • Visualizzazioni: 39,2k

Smontaggio

Cosa ti serve

Questo smontaggio non è una guida di riparazione. Per riparare il tuo Xbox 360 Wireless Controller, usa il nostro manuale di assistenza.

  1. Xbox 360 Wireless Controller Teardown, Removing the first screws: passo 1, immagine 1 di 3 Xbox 360 Wireless Controller Teardown, Removing the first screws: passo 1, immagine 2 di 3 Xbox 360 Wireless Controller Teardown, Removing the first screws: passo 1, immagine 3 di 3

    • Place the controller face down on your working surface to allow access to rear screws.

    • Take the battery compartment out.

    • Use a TR9 bit and screwdriver to remove all 7 screws.

    Modifica

  2. Xbox 360 Wireless Controller Teardown, Removing the back: passo 2, immagine 1 di 2 Xbox 360 Wireless Controller Teardown, Removing the back: passo 2, immagine 2 di 2

    • Remove the rear half of the controller by pulling perpendicular to the front half.

    • The battery terminals have specific grooves that they slide in and out of.

    • If the two halves do not easily separate, you can slide a spudger along the seam and/or slightly depress the left/right triggers.

    Modifica

  3. Xbox 360 Wireless Controller Teardown, Removing the vibration motors: passo 3, immagine 1 di 2 Xbox 360 Wireless Controller Teardown, Removing the vibration motors: passo 3, immagine 2 di 2

    • Detach the vibration motor cable from the PCB.

    • DO NOT use the cable to remove from the PCB. You may damage the motor, connector, or PCB by pulling on the cable.

    • After detaching the vibration motor cable from the PCB, remove the vibration motor.

    • Utilize the same technique for the other vibration motor on the opposite side.

    Modifica

    I might Xbox one controller the left thumb stick sticks how do I clean it without tools

    kenn Bucek - Replica

  5. Xbox 360 Wireless Controller Teardown, Removing the PCB: passo 4, immagine 1 di 2 Xbox 360 Wireless Controller Teardown, Removing the PCB: passo 4, immagine 2 di 2

    • Make sure the front half of the controller is facing towards you.

    • The PCB should simply lift out with little to no force when being held by the areas highlighted.

    • If the PCB doesn't freely lift out, apply light consistent leverage under the highlighted area.

    • Be cognizant of the components on the opposing side of the PCB.

    Modifica

    How do i remove the little springs for the battery area and put new ones in

    Final - Replica

  6. Xbox 360 Wireless Controller Teardown: passo 5, immagine 1 di 1

    • Full IC Identification:

    • You may need to enlarge it to view the text.

    Modifica

  7. Xbox 360 Wireless Controller Teardown, Removing the buttons and the bumper: passo 6, immagine 1 di 3 Xbox 360 Wireless Controller Teardown, Removing the buttons and the bumper: passo 6, immagine 2 di 3 Xbox 360 Wireless Controller Teardown, Removing the buttons and the bumper: passo 6, immagine 3 di 3

    • Gently peel off the conductive rubber pads to expose the backsides of the buttons

    • Remove the A, B, X, Y, Back, Start and Guide buttons. The Guide button sleeve may also be removed.

    • You can now remove the bumper assembly at the top.

    Modifica

  8. Xbox 360 Wireless Controller Teardown, Removing the D-Pad: passo 7, immagine 1 di 1

    • Remove the last two screws in the D-pad with a #0 Phillips screwdriver.

    • Use a pair of tweezers to squeeze the clips together and remove the D-pad.

    Modifica

  9. Xbox 360 Wireless Controller Teardown, End result: passo 8, immagine 1 di 1

    • And here is the final result: a completely disassembled Xbox 360 Wireless Controller.

    Modifica

Autore

con 7 altri collaboratori

Mart-Jan

Membro da: 05/26/19

305 Reputazione

1 Guida realizzata

Distintivi: 0

3 Commenti

Excelente trabajos

RIGO NOLASCO - Replica

Very clear, helped me clean my controller. Thank you :)

Taydolf Swiftler - Replica

Hello. I just did clean one of mine that i did bye 2011. The Rumble on left end right are the opposit to this guide.

I did never disconnect them from the pcb. So ma bey its another revision or the left and right is missing.

From the back.

Small left , big right.

https://imgur.com/a/DxXdUNB

Michael Orban - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 24

Ultimi 7 Giorni: 176

Ultimi 30 Giorni: 996

Tutti i Tempi: 39,294