Strumenti necessari in questo Smontaggio

Introduzione

This guide will show you how to completely teardown your camera.

Questo smontaggio non è una guida di riparazione. Per riparare il tuo Olympus Stylus 410, usa il nostro manuale di assistenza.

Locate the 2 screws on the bottom of the slider.
  • Locate the 2 screws on the bottom of the slider.

  • Remove both screws with a #00 Phillips screwdriver.

Aggiungi Commento

Gently pull on the bottom of the slider until it comes off the lower track.
  • Gently pull on the bottom of the slider until it comes off the lower track.

  • There is a little piece that connects the slider to the track. Be sure not to lose this as it is needed to put the slider back on.

Aggiungi Commento

  • Lift the slider up until it comes off the upper track.

Aggiungi Commento

  • The slider should now be free from the body of the camera.

Aggiungi Commento

  • Locate the 3 screws on the outer metal band and remove them with a #00 Phillips screwdriver.

Aggiungi Commento

  • Use the spudger to peel off the outer metal band, starting from the bottom of the camera.

  • The metal band it attached to the camera with glue in addition to screws. Be careful not to bend the band when removing it from the camera.

Aggiungi Commento

  • The shutter button can now be removed. It is not connected to the camera and can be lifted off.

Aggiungi Commento

  • Remove the memory card.

  • Locate and remove the 2 screws using a #00 Phillips screwdriver.

Aggiungi Commento

  • Use a spudger around the edge of the case to loosen it.

  • Carefully wiggle the back case off. This may require a fair amount of force.

Aggiungi Commento

  • Locate the 3 internal screws holding on the front of the case. Remove them with a #00 Phillips screwdriver.

Aggiungi Commento

  • While grasping the interior and the front case, gently pull until they start to come apart. Some light wiggling may be required.

  • Be careful not to completely pull the front case off because it will still be connected with wires.

Aggiungi Commento

  • Locate the gray compartment covering the flash.

  • Position your flat head screw driver or small spudger underneath the tab that is keeping the gray cover on.

  • Gently lift the tab so the gray compartment becomes free.

Aggiungi Commento

  • Use the spudger around the perimeter of the gray compartment to detach it from the front case.

  • The gray compartment can now be removed from the flash unit.

  • The flash unit can now be removed, and a new one soldered back on.

Aggiungi Commento

  • Open the battery cover and lift it up and off of back camera case.

Aggiungi Commento

  • Locate and unscrew the 2 screws with a #00 Phillips screwdriver.

  • Remove the black seal.

Aggiungi Commento

  • Slide the metal piece off of the battery cover.

Aggiungi Commento

  • This is what the battery cover and back case look like completely disassembled.

Aggiungi Commento

  • Remove the metal frame from the LCD screen using a spudger.

Aggiungi Commento

  • Pry off the LCD screen from the top using a spudger. The screen will not be completely free from the device because of a ribbon.

  • Do not pull the screen completely off because it will still be held on by two ribbon cables.

Aggiungi Commento

  • This is what the camera will look like now that the LCD screen is removed.

Aggiungi Commento

Rory Aronson

Membro da: 15/04/2010

34 Reputazione

6 Guide realizzate

Team

Cal Poly, Team 6-13, Maness Spring 2010 Membro di Cal Poly, Team 6-13, Maness Spring 2010

CPSU-MANESS-S10S6G13

5 Membri

9 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 2

Tutti i Tempi: 4,411