Salta al contenuto principale

Cosa ti serve

Questo smontaggio non è una guida di riparazione. Per riparare il tuo Linksys Velop WHW01, usa il nostro manuale di assistenza.

  1. Linksys Velop WHW01 Teardown, Unclip the top cover: passo 1, immagine 1 di 2 Linksys Velop WHW01 Teardown, Unclip the top cover: passo 1, immagine 2 di 2
    Attrezzo utilizzato in questo passaggio:
    Jimmy
    $7.95
    Compra
    • To unclip the top cover, insert a Jimmy at the seam and pry upwards.

  2. Linksys Velop WHW01 Teardown, Unscrew the outer case: passo 2, immagine 1 di 2 Linksys Velop WHW01 Teardown, Unscrew the outer case: passo 2, immagine 2 di 2
    Attrezzo utilizzato in questo passaggio:
    T6 Torx Screwdriver
    $9.99
    Compra
    • Use a Torx T6 screwdriver to unscrew the two screws that were previously hidden under the top cover.

  3. Linksys Velop WHW01 Teardown, Remove the rubber strips: passo 3, immagine 1 di 2 Linksys Velop WHW01 Teardown, Remove the rubber strips: passo 3, immagine 2 di 2
    Attrezzo utilizzato in questo passaggio:
    Spudger
    $2.99
    Compra
    • Use a Spudger to peel off the rubber strips at the base.

    • Make sure to not tear them apart.

  4. Linksys Velop WHW01 Teardown, Unscrew the base: passo 4, immagine 1 di 3 Linksys Velop WHW01 Teardown, Unscrew the base: passo 4, immagine 2 di 3 Linksys Velop WHW01 Teardown, Unscrew the base: passo 4, immagine 3 di 3
    Attrezzo utilizzato in questo passaggio:
    T6 Torx Screwdriver
    $9.99
    Compra
    • Use a Torx T6 screwdriver to unscrew the four screws that were under the rubber feet.

    • After removing the screws, the bottom cover can be lifted off.

  5. Linksys Velop WHW01 Teardown, Remove the outer cover: passo 5, immagine 1 di 3 Linksys Velop WHW01 Teardown, Remove the outer cover: passo 5, immagine 2 di 3 Linksys Velop WHW01 Teardown, Remove the outer cover: passo 5, immagine 3 di 3
    • Carefully pinch and pull up on the internal plastic bracket.

    • The main board, antenna and LED assembly should slide out without any force needed.

  6. Linksys Velop WHW01 Teardown, Remove the port cover: passo 6, immagine 1 di 2 Linksys Velop WHW01 Teardown, Remove the port cover: passo 6, immagine 2 di 2
    • Lift up on the plastic surrounding the power input and ethernet ports.

    • You may need to give it a jiggle to come loose.

  7. Linksys Velop WHW01 Teardown, Unclip the WiFi antenna: passo 7, immagine 1 di 1
    Attrezzo utilizzato in questo passaggio:
    Spudger
    $2.99
    Compra
    • Unclip the WiFi antennas from the main board.

    • Use a Spudger to not cause any damage, these connectors can be very fragile!

  8. Linksys Velop WHW01 Teardown, Unscrew the antenna bracket: passo 8, immagine 1 di 1
    Attrezzo utilizzato in questo passaggio:
    Phillips #00 Screwdriver
    $5.49
    Compra
  9. Linksys Velop WHW01 Teardown, Slide out the LED module: passo 9, immagine 1 di 3 Linksys Velop WHW01 Teardown, Slide out the LED module: passo 9, immagine 2 di 3 Linksys Velop WHW01 Teardown, Slide out the LED module: passo 9, immagine 3 di 3
    • Carefully pull the LED module out of the groove its slid into.

    • Be careful with the highly fragile ribbon cable, it is soldered on the LED and main board and does not detach!

  10. Linksys Velop WHW01 Teardown, Remove the antenna bracket: passo 10, immagine 1 di 1
    • Lift off the antenna bracket, being mindful of the LED module.

  11. Linksys Velop WHW01 Teardown, Unclip the bluetooth antenna: passo 11, immagine 1 di 1
    • Unclip the Bluetooth antenna, the same procedure as the WiFi antennas.

  12. Linksys Velop WHW01 Teardown, Remove the plastic bracket: passo 12, immagine 1 di 3 Linksys Velop WHW01 Teardown, Remove the plastic bracket: passo 12, immagine 2 di 3 Linksys Velop WHW01 Teardown, Remove the plastic bracket: passo 12, immagine 3 di 3
    Attrezzo utilizzato in questo passaggio:
    Phillips #00 Screwdriver
    $5.49
    Compra
    • Use a Phillips #00 Screwdriver to unscrew the screw holding the rear plastic bracket.

    • Turn the assembly around and lift the bracket off the main board.

  13. Linksys Velop WHW01 Teardown, Remove the front heatsink: passo 13, immagine 1 di 3 Linksys Velop WHW01 Teardown, Remove the front heatsink: passo 13, immagine 2 di 3 Linksys Velop WHW01 Teardown, Remove the front heatsink: passo 13, immagine 3 di 3
    Attrezzo utilizzato in questo passaggio:
    Phillips #00 Screwdriver
    $5.49
    Compra
    • Use a Phillips #00 Screwdriver to unscrew the three screws securing the heatsink.

    • After removing the screws you will need to twist it side to side a little bit due to the thermal pad.

  14. Linksys Velop WHW01 Teardown, Remove the back heatsink: passo 14, immagine 1 di 1
    • After removing the upper heatsink, the heatsink on the back of the board can be removed using a similar process to the top heatsink.

    • Only small and gentle side to side movement is needed to release the thermal pads.

4 Commenti

Very well done! In terms of disassembly, how long did it take to get everything apart?

Jacob Mehnert - Replica

definitely no longer than 10 mins, even shorter if you are only going in to access the serial port for flashing a custom firmware

Lewis L. Foster -

Great information, thank you for doing this! Did I see a proprietary antenna connector and no ts9?

Courtney Glenn - Replica

Not really clued up on my antennas so not sure

Lewis L. Foster -

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 25

Ultimi 30 Giorni: 85

Tutti i Tempi: 3,186