Salta al contenuto principale

Cosa ti serve

Questo smontaggio non è una guida di riparazione. Per riparare il tuo 2010 Telstra t-box, usa il nostro manuale di assistenza.

  1. 2010 Telstra t-box Teardown, Preparation: passo 1, immagine 1 di 1
    • Place your system on a flat surface and make sure all cables are disconnected from the system before dissasembly

  2. 2010 Telstra t-box Teardown, Remove case from bottom: passo 2, immagine 1 di 1
    • Flip the device over and remove the hard drive cover (I dont have a hard drive cover on my t-box)

    • Peel off the warranty sticker and remove the 4 screws

  3. 2010 Telstra t-box Teardown, Opening it up: passo 3, immagine 1 di 1
    • Pull the casing off being careful of the cables connected to the case.

    • carefully disconnect those cables and proceed

  4. 2010 Telstra t-box Teardown, Getting inside: passo 4, immagine 1 di 1
    • After disconnecting the cables, you can remove the top half of the outer case.

  5. 2010 Telstra t-box Teardown, Disconnecting the USB wifi adapter: passo 5, immagine 1 di 1
    • remove the black tape holding the USB wifi adapter in place, then remove it the same way you would remove a USB stick

  6. 2010 Telstra t-box Teardown, Removing the IR sensor's board: passo 6, immagine 1 di 3 2010 Telstra t-box Teardown, Removing the IR sensor's board: passo 6, immagine 2 di 3 2010 Telstra t-box Teardown, Removing the IR sensor's board: passo 6, immagine 3 di 3
    • remove the ribbon cable on both ends and then carefully remove the IR sensor's board from the device

    • Please note that there is a metal tab thing holding the board in place, pull it a little bit and remove the board

  7. 2010 Telstra t-box Teardown, Removing the Main Board and hard drive: passo 7, immagine 1 di 3 2010 Telstra t-box Teardown, Removing the Main Board and hard drive: passo 7, immagine 2 di 3 2010 Telstra t-box Teardown, Removing the Main Board and hard drive: passo 7, immagine 3 di 3
    • Remove the screws holding the circut board in place

    • There is a screw on the hard drive cover next to the board, remove it

    • remove the hard drive and you should be able to get the main board

  8. 2010 Telstra t-box Teardown, And you're done!: passo 8, immagine 1 di 3 2010 Telstra t-box Teardown, And you're done!: passo 8, immagine 2 di 3 2010 Telstra t-box Teardown, And you're done!: passo 8, immagine 3 di 3
    • Take some nice pics of the t-box

    • To put it back together, do all these steps in reverse

Bryn Trainor

Membro da: 04/25/19

314 Reputazione

1 Guida realizzata

5 Commenti

once you’ve taken it apart, can it be repaired? we have lost picture … can’t play ANY recoded material (100 hours worth) … what to do?

omarty - Replica

It’s exactly the same as few other boxes, this is a Netgem N8200, comes with different model designations depending of hard drive, etc… N8200-320-2T, N8200-160-2T, N8500-…

BITS2 - Replica

I am no longer using this device with telstra-

Is there anything in there that could be used for anything else other than the t-box??

Or do I throw it in the bin!

Steve - Replica

@steve75385 Don't throw it it the bin! Send it to me. I would like to use the mechanical spinning thing that's encased in a silver aluminium box

ww w -

Is there a way to get recorded things off the hard drive? I have several movies on mine and the tbox won't power on any more.

Deanne Roberts - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 4

Ultimi 30 Giorni: 19

Tutti i Tempi: 2,108