⟐ Commented giugno 26, 2023 at 10:40 GMT-7

⟐ Answered settembre 05, 2023 at 12:16 GMT-7

⟐ Answered marzo 19, 2020 at 12:06 GMT-7

⟐ Commented gennaio 19, 2025 at 15:06 GMT-7

⟐ Answered aprile 20, 2024 at 1:27 GMT-7

⟐ Answered maggio 06, 2023 at 7:47 GMT-7

Hi everyone, I’ve bought on Ebay.it two dock charge flex cable(1 for iPhone 8 Plus and 1 for iPhone XS) sold as original Apple. But in iPhone 8 Plus flex cable, Apple logo is missing or covered by a silver circle instead in iPhone XS(mic doesn’t work) flex cable serial and logo are different from the original one installed in the phone. That one with dani written is original.

⟐ Answered febbraio 23, 2022 at 4:31 GMT-7

dopo aver sostituito lo schermo al mio iPhone XS, il tutto ha funzionato correttamente per una giornata. Il giorno dopo, all’accensione, lo schermo è rimasto acceso per 30 sec e poi è diventato nero, restando acceso e con possibilità di ricevere notifiche e spegnerlo regolarmente (il touch funziona anche a schermo nero).

E’ un difetto dello schermo o c’è altro? Ho già provato a fare un hard reset del dispositivo e scollegato e ricollegato tutti i contatti ma con esisto negativo.

Grazie

⟐ Answered agosto 12, 2021 at 0:22 GMT-7

ho cambiato lo schermo e il flat speaker voce sensore prossimità. Il telefono si accende normalmente e ovviamente non funziona il face id, Il problema è che non mi riconosce il codice di sblocco per sbloccare il telefono rendendolo quindi inusabile visto che non si può sbloccare con il face id e non riconosce il codice di sblocco. Dice sempre che è sbagliato.

E’ possibile che cambiando il flat sia cambiato da solo il codice di sblocco??

A qualcuno è già successa questa cosa?

Grazie in anticipo

⟐ Answered gennaio 04, 2021 at 1:22 GMT-7

Grazie :)

⟐ Commented settembre 10, 2020 at 5:19 GMT-7

⟐ Answered ottobre 17, 2024 at 3:14 GMT-7

any help shall be highly appreciated,

Thanks.

⟐ Commented settembre 14, 2025 at 7:54 GMT-7

Is the iPhone X display compatible with the iPhone XS? On paper they look the same. They even have the same number of pins in both connectors. But there is still no confirmation of anyone who has tried it.

I hope someone has an answer for this.

⟐ Commented ottobre 18, 2022 at 12:37 GMT-7

But when I try to set up new face ID my iPhone tells me "move little lower", then "move little higher", also make blur and so infinitely. Sometimes iPhone says that it can't set up new FaceID. The fact is that I damaged ambien light sensor when were transfering FaceID module to a new display cause it was very damaged by sea salt. I think that it influence to FaceID working. And now I want to buy "iPhone XS 5.8 Ear Speaker Proximity Ambient Light Sensor Flex Cable w/ Brackets". But I'm not sure that Face ID will work after replacing it. I'm afraid that i need to buy iPhone XS Facing camera module too. (frontal camera, dot projector and infared camera)

I dont know how to know it works or no, so i tell you all symptoms that I observe. And I dont know, what if I change ambient light sensor and speaker my phone may tells me that FaceID cannot be installed cause it not paired with motherboard, frontal camera or other. I dont understand could I replace only ambient light sensor module if all rest modules are working.

So, I describe all symptoms:

- FaceID fails to detect a face during the setup process. Keeps sending the two messages: move iPhone a little lower/higher and makes blur sometimes

- Animoji works fine.

- Frontal camera works perfectly, but portrait mode not functioning.

- Both of back cameras works fine and portrait mode works too.

- I dont see anything lights through the camera of my other iPhone for check Flood illuminator works or not. I dont see a light of dot projector, but i thenk it cause it should turn off after lights of flood illuminator and proximity sensor.

- When picking up the phone it turn on the display

- I have tried of types of reset.

So, i'm waiting for your respond and I need help so much. Cause I need to know - I need to buy only "ambient light sensor" module or I need to buy it with a "frontal camera" module.

Could I get an issue than FaceID is unavaivable for my phone if I replace only ambient light sensor or no? Or maybe ambient light sensor nothing to do with? Maybe it all cause I move all Face ID and Speaker modules to a new display? Waiting for your help.

⟐ Answer edited ottobre 08, 2020 at 19:25 GMT-7

I’ve noticed that sometimes, tapping it or setting it down will cause it to turn off. It will eventually turn itself off randomly, even if held in my hand or resting on a table, with the frequency increasing the more I turn it on and it dying until I leave it to rest. I double-checked all connections during the repair and tested the phone before reassembling to ensure everything works, with no issues. I had the battery unplugged while connecting the screen to ensure no discharge or damage. My first thought was the battery, but the battery is brand new and did not pose any symptoms or problems prior to me replacing the screen.

Why is this happening? I’ve heard some theories about components making direct contact with other parts of the phone’s internals which could cause problems. The screen I bought, while 3rd party and LCD, is from a reputable manufacturer (as far as 3rd party parts go), was bought brand new, and from a trustworthy seller. The screen is fully functional, so I’m less inclined to believe the screen is defective.

⟐ Answered maggio 30, 2025 at 7:11 GMT-7

Regards folks!

⟐ Commented dicembre 04, 2025 at 17:05 GMT-7

⟐ Answered dicembre 01, 2022 at 13:54 GMT-7

When that happens, the shown battery filling level drops to 0% and shortly after it will reboot with the mentioned error in the panic logs.

First I suspected that the error might be related to the lightning port. But replacing it didn’t fix it.

⟐ Commented luglio 24, 2025 at 21:29 GMT-7

I cleaned out the connector and tried reseating several times. I also tried with another screen. Both are able to display an image but touch does not work. Neither are OEM screens.

Is there a common issue with the iPhone XS with replacement screens due to some kind of digitizer programming or is the ribbon cable to the digitizer particular sensitive? Or is it possible the board being damaged due to the entire phone being bent about 15 degrees?

⟐ Answer accepted giugno 15, 2019 at 8:52 GMT-7

⟐ Answered ottobre 27, 2024 at 18:30 GMT-7