⟐ Answered ottobre 20, 2022 at 20:11 GMT-7

come posso fare?

⟐ Answered luglio 22, 2022 at 4:25 GMT-7

⟐ Answered ottobre 24, 2024 at 14:51 GMT-7

Ho già effettuato i seguenti controlli:

1. Verificato e pulito i connettori del display con alcol isopropilico.

2. Controllato che non ci siano pin piegati.

3. Escluso altre cause hardware comuni.

Qualcuno ha riscontrato problemi simili con i pannelli LCD In-Cell su iPhone 12? Potrebbe trattarsi di un'incompatibilità software o di un difetto specifico del componente che richiede una sostituzione in garanzia? Grazie per l'aiuto!

⟐ Answer accepted giugno 08, 2026 at 13:36 GMT-7

Inoltre anche la batteria si scarica più veloce rispetto a prima. Un installazione fatta male o un display scadente possono effettivamente portare danni alla batteria? Sono consapevole che il display non è originale ma non so se c’è una correlazione

⟐ Answered agosto 17, 2025 at 4:42 GMT-7

⟐ Answered settembre 21, 2022 at 23:46 GMT-7

Anzi, modifico la domanda: quali sono gli elementi che proprio non è possibile sostituire senza perdere funzionalità importanti?

dopo il mio solito giro in moto domenicale, la fotocamera 1x del mio iPhone 12 ha smesso di funzionare correttamente. Continua a vibrare e non mette a fuoco. Allego un video della fotocamera.

Cosa potrebbe essere?

Grazie.

P.S: la fotocamera 0.5x funziona perfettamente senza problemi

Because of the square edge design of the iPhone 12 and the new glue being used, I was concerned about how I would get the screens off without them cracking, so I heated the phones up to 90 degrees, used a pry tool to get the screen out of the frame slightly and then used Isopropanol to degenerate the glue.

I did not disconnect the screens when I did the battery replacement.

Could the Isopropanol be trapped in the phone causing some issues or is this because of the battery, which I doubt. The third phone seems to be ok.

⟐ Commented maggio 20, 2024 at 2:22 GMT-7

⟐ Answered agosto 10, 2023 at 9:28 GMT-7

⟐ Answered febbraio 07, 2021 at 10:46 GMT-7

I seen this once before, but did not think much of it at the time since the phone was fine. However, the issue was still there when I remembered someone saying they needed a donor camera to fix theirs. I didn’t want it even for parts due to the issue it has (bad aperture assembly, part is NLA but has what they need). Since I knew they were looking, I found sent a link (and those photos on what needs to be done to do the swap, being my 2nd round with this fault in the sense one bad a bad door and the other had a bad LCD but good door and I had a good LCD to swap over). The issue appeared again.

Is this look like a camera issue or a lighting issue with my phone?

⟐ Answer accepted ottobre 15, 2022 at 10:03 GMT-7

⟐ Answered dicembre 22, 2023 at 9:13 GMT-7

In iFixIt guides they call for the 00 Philips screw driver but in Apple's own self service guides and tool purchases/rentals it says JCIS bit. I know the differences between PH and JCIS is very minimal but it still seems somewhat important to know the difference.

So basically, regardless of how much it may or may not matter, which is the actual 100% correct tool? Does apple use JCIS screws instead of Philips or???

Thank you.

⟐ Commented settembre 29, 2025 at 18:55 GMT-7

⟐ Answered luglio 30, 2023 at 20:24 GMT-7

⟐ Answer edited marzo 02, 2025 at 17:47 GMT-7

On iOS 18 and newer, authenticate your new battery using Apple's Repair Assistant.

And...

After your repair, depending on the replacement part, you may be able to calibrate it using Apple's Repair Assistant, available as of iOS 18. Update your device, navigate to Settings → General → About → Parts & Service History, tap Restart & Finish Repair, and follow the onscreen prompts.

I did this, but it still says the battery is "unknown". My battery was iFixit brand, not Apple. But in the repair guide it sounds like this should work either way. Has anyone gotten this to work with an iFixit brand battery in iOS 18?

⟐ Commented dicembre 28, 2024 at 9:45 GMT-7

the screen is broken

the screen does not power on

the charging port was ever so slightly loose when i opened the phone

i tightened it and now its sturdy

Everythibg else seems ok

But

I didnt get any response (vibration) when touching or power button (screen was not attached)

No response from charging, wirless or normal port charging

So

Is this because theres no screen and thus will change when i replace screen?

Or could it be a problem with another part?

Help me how you can, thx ifixit family

⟐ Answer accepted ottobre 25, 2022 at 9:40 GMT-7

⟐ Answer edited giugno 15, 2026 at 20:28 GMT-7