⟐ Answered dicembre 09, 2022 at 12:06 GMT-7

Oppure si spegne e si riavvia da solo.

⟐ Answer accepted dicembre 01, 2022 at 9:18 GMT-7

Dopo riparazione con sostituzione del display, il tasto home “balla”, parte dello schermo non è stabile (si schiaccia, si alza): penso sia solo un problema di colla. Risolvo con l’assistive Touch e bona.

Dopo qualche mese, la parte sinistra del del display non funziona con il touch. Potrebbe essere sufficiente sostituire il display?

⟐ Answered marzo 11, 2021 at 1:23 GMT-7

Sono esattamente adiacenti al connettore del display.

⟐ Edited by author maggio 31, 2020 at 3:30 GMT-7

⟐ Answered aprile 23, 2020 at 2:02 GMT-7

⟐ Answer accepted aprile 06, 2019 at 10:01 GMT-7

⟐ Commented febbraio 20, 2019 at 11:43 GMT-7

Mi servirebbe lo schema elettrico iPad 3 mini A 1599 per effettuare delle riparazioni sulla scheda madre

Grazie

Dopo 4 cambi lcd il connettore del touch si è rotto, nel cambiarlo il contatto tutto a destra in alto (non quello neo bordi) sulla scheda madre, si è rotto. Possibile ripristinare la pista mancante sulla scheda? Grazie Gregory

⟐ Answered giugno 18, 2016 at 15:35 GMT-7

⟐ Answer edited maggio 27, 2026 at 15:44 GMT-7

i always had a display protection glass on my ipad, and a case around it, which covers every corner. The protection glass is perfectly intact, the crack is underneath it. I have no idea how this happened. But i think, Apple won’t believe me that its not my fault, so i don’t want to take it to the store.

So I’d like to replace the display by myself. But i can’t seem to find it anywhere. Do you have any idea where to get one or why there isn’t any?

⟐ Commented maggio 25, 2026 at 8:22 GMT-7

⟐ Answered aprile 20, 2026 at 14:09 GMT-7

⟐ Answered aprile 04, 2026 at 6:45 GMT-7

⟐ Commented febbraio 23, 2026 at 1:46 GMT-7

⟐ Commented febbraio 19, 2026 at 7:26 GMT-7

I was playing with the PC interface and had the micro USB port going to my PC and had my 140-watt universal charging pack going to the USB-C input port and would plug devices to charge into the USB-C output port. I've used this before with my phone and a MacBook Pro I repaired, and I was getting mixed results.

Sometimes when I plugged the devices in, it would call for fast charging, and sometimes it would only low charge or not charge at all, and I couldn't figure out why. On this day I would plug in my iPhone 17 Pro, and it would only draw 5 volts and less than 1 amp, but the phone was almost fully charged, so I decided to plug in my iPad mini, and it was charging, but at some point, while going through the settings, I noticed the iPad charging indicator started going off and on, so I eventually unplugged everything from the tester, plugged my 140-watt charger into the iPad, and walked away.

Later that night I noticed my iPad was almost dead after being on the charger all day, so I plugged it into a USB-C Anker pack to see what's up, and when I plug the iPad into it, it immediately kicks the power bank off.

I wasn't sure what was up, so I plugged the iPad into my PC, which gave an error stating that the device I plugged in was calling for too much power or something like that.

I've since removed the screen to take a look, and what I've found is that it definitely isn't the port because when I unclip the port's ribbon cable and plug into it, the charger pack stays on fine, but when the port is reattached to the logic board, it immediately shuts down, so I'm assuming there's a short somewhere, but I'm not 100 percent sure where to look.

I also charged the battery with my bench-top power supply at 4 volts and 1.5 amps externally and got it almost fully charged so I could back up my iPad, so the battery seems to be fine too.

I can't seem to find a board view file or schematic anywhere, so I'm looking for anyone who may have dealt with a similar problem or may have suggestions on where to look. I do have the ability to do voltage injection with a thermal camera, I'm just not sure where I should inject. Thanks for any help.

⟐ Edited febbraio 06, 2026 at 7:06 GMT-7

I understand that a screen replacement is the only way to fix something like this, as it’s the display likely being damaged, but if I were to replace the screen I would want to be sure that it wouldn’t happen again with a new screen, since they’re expensive to replace.

Just received a refurbished iPad mini from eBay that otherwise seems great but when dark mode turned on noticed these blotches that only appear on dark background. Are they stuck pixels? Would those flashing colour videos or massaging them (I have an Apple Pencil I could apply pressure with) help or does this look more serious?

The seller offers a warranty and eBay has their guarantee but curious if it’s an issue that can be fixed without having to send it back.

⟐ Answered gennaio 14, 2026 at 7:24 GMT-7

⟐ Answered gennaio 02, 2026 at 10:23 GMT-7