As the title says, I can’t get the wipe & reinstall to finish. Here’s what I’ve checked so far:

• The new SSD (VIPER VP4000 Mini 500GB M.2 2230 PCIe Gen4 x4 SSD - Solid State Drive - VP4000M500GM23 )shows up in the partition manager, so the Deck does recognize it

• I put the SteamOS recovery image on a 16GB USB stick using the tool recommended on the Steam support page

• Note: the USB stick had ~0.5GB of existing files on it before I flashed it (which I backed up first), not sure if this is causing issues.

Every time I start the reinstall, Konsole opens, executes a few lines, and then just closes, it happens quick, can’t see errors because it closes too fast, no completion, nothing.

Things I’m wondering about:

1. Could the pre-existing files on the USB stick have caused the flash to go wrong? Should I fully wipe and put the recovery img on it again? Would just deleting everything count as a full wipe or do I need to do something else (im on a Macbook).

2. Could the newness of the SSD be causing issues? I can see it in partition manager but haven’t checked whether it’s GPT or something.

3. Is there anything in the recovery process I might be missing? Or anybody had a similar experience?

Any help appreciated: happy to provide more details if needed!

⟐ Edited by author luglio 04, 2026 at 6:48 GMT-7

Steamdeck has been feeling a little unresponsive lately then after I left it for a bit (picked up Elden rings finally) I noticed the entire lefts side was completely dead. All buttons, joystick, triggers, trackpad ect. I followed all the software resets to make sure then followed a guide here hoping that if I opened it up it would be a simple disconnect ribbon. As seen in the attached picture the C-L connector appears to have short circuited or something, I am not a tech savvy person and am unclear how to move forward. Would this require a while board replacement or something bigger, any advice on how to move forward or what I could do would be greatly appreciated!

I have a steamdeck LCD. After not using it for a few weeks i wanted to turn it on and play with it etc, the power LED comes on and fan turns, but no display.

Ive tried some guides I found about reseting firmware by holding down "..." and volume down button, it comes on, LED flashes but no display, even after waiting a few hours for this process to complete, I have also tried using a docking station to see if i get any display, now the problem is i dont know if the docking station i used is compatible with the steam deck, but it is a dell self powered docking station, dont want to spend the money if the problem lays elsewhere.

Any suggestions would be appreciated.

⟐ Edited by author giugno 29, 2026 at 0:29 GMT-7

⟐ Commented giugno 25, 2026 at 23:39 GMT-7

⟐ Answered giugno 24, 2026 at 20:19 GMT-7

⟐ Commented giugno 24, 2026 at 20:17 GMT-7

⟐ Answered giugno 24, 2026 at 20:10 GMT-7

Thank you for any help

⟐ Answered giugno 18, 2026 at 11:53 GMT-7

I have a Steam Deck OLED which has a damaged surface-mount connector that connects the internal display to the device. I have no idea where to find this part, and Steam Support refused to give me the name of it. I heard from someone else that a repair tech was able to use a connector from a Surface Pro as an equivalent, but it's hard to find info on that too.

Otherwise, I'm guessing I'll have to find an equivalent based on the length, width, height, no. of pins, pitch, etc. on Mouser or something but I'm not sure what this double-decker style of pins is called that is on this flex cable (I usually work with very old electronics so I haven't seen this before), so if anyone knows what the official name for that is it'll give me one more parameter to source a replacement.

Thanks in advance.

An image of the connector can be found through the following link on Ifixit's guide to replacing the OLED screen: https://guide-images.cdn.ifixit.com/igi/...

⟐ Commented giugno 04, 2026 at 13:00 GMT-7

Does anyone have any tips or advice as to how I can get this screw out? I’ve trying applying upward pressure (as in trying to pull the front and back shells apart near this joint) whilst turning the screw, but nothing.

The screw head/drive is not stripped as I can see it turning.

⟐ Commented maggio 26, 2026 at 10:18 GMT-7

I can’t pinpoint the cause because it’s very unpredictable. Sometimes, I can use the trackpad normally, and the next second, it suddenly stops working.

I’ve already tried factory resetting the device, but the problem persists. I’ve also tried updating to the beta version, but that didn’t help either.

Interestingly, the trackpad always worked when I was in BIOS mode, so I’m assuming it’s a software issue.

⟐ Answered maggio 22, 2026 at 0:46 GMT-7

⟐ Commented maggio 20, 2026 at 15:54 GMT-7