Salta al contenuto principale
Aiuto

Versione corrente di: Chris Green ,

Testo:

There's aren't any great guides for JTAGing anywhere. The one that I used my first time was [http://www.se7ensins.com/forums/topic/108432-how-to-do-the-jtag-hackdump-nandxell/|This Guide] on Se7enSins. It will show you how to identify your console, do the wiring, and flash XeLL, flashing a rebooter is the next step after doing that. You will also need [http://www.ebay.com/itm/100-Ohm-1-2-Watt-5-Carbon-Film-Resistors-35pcs-/190494300933?pt=LH_DefaultDomain_0&hash=item2c5a585b05|100 Ohm Resistors] (You have to buy them in bulk, but they're cheap) and [http://www.ebay.com/itm/1N4148-High-Speed-Switching-Diodes-100-pcs-/180597395202?pt=LH_DefaultDomain_0&hash=item2a0c718f02|1N4148 Diodes] (Also in bulk, but cheap) For the wiring, I recommend using non-braided (solid core) CAT5 wire. Good luck with your JTAG!
 
Also, some advice:
 
-Solder your resistors, and diodes to the xbox's motherboard, then solder the wires to them.
 
-Make sure that you have two identical NAND dumps before flashing anything to the console.
-make
-make
sure that you erase the flash ("nandpro lpt: -e400") before writing any image to it. (XeLL, original NAND, and any rebooter)
-When


-When
doing your wiring, you don't need an actual LPT cable, you can just feed the wires attatched to the console's motherboard into your PC's LPT port.
-make
-make
sure that you erase the flash ("nandpro lpt: -e400") before writing any image to it. (XeLL, original NAND, and any rebooter)
-When


-When
doing your wiring, you don't need an actual LPT cable, you can just feed the wires attatched to the console's motherboard into your PC's LPT port.
-Most Importantly, if you console is on the 2.0.8***.0 or newer dashboard, IT IS NOT JTAG-ABLE! Trying to JTAG it will only brick the flash controller, and render the console useless. (You won't be able to flash back original NAND)

Stato:

open

Modifica di: Chris Green ,

Testo:

There's aren't any great guides for JTAGing anywhere. The one that I used my first time was [http://www.se7ensins.com/forums/topic/108432-how-to-do-the-jtag-hackdump-nandxell/|This Guide] on Se7enSins. It will show you how to identify your console, do the wiring, and flash XeLL, flashing a rebooter is the next step after doing that. You will also need [http://www.ebay.com/itm/100-Ohm-1-2-Watt-5-Carbon-Film-Resistors-35pcs-/190494300933?pt=LH_DefaultDomain_0&hash=item2c5a585b05|100 Ohm Resistors] (You have to buy them in bulk, but they're cheap) and [http://www.ebay.com/itm/1N4148-High-Speed-Switching-Diodes-100-pcs-/180597395202?pt=LH_DefaultDomain_0&hash=item2a0c718f02|1N4148 Diodes] (Also in bulk, but cheap) For the wiring, I recommend using non-braided (solid core) CAT5 wire. Good luck with your JTAG!
 
Also, some advice:
 
-Make sure that you have two identical NAND dumps, and makedumps before flashing anything to the console.
-make
sure that you erase the flash ("nandpro lpt: -e400") before writing any image to it. (XeLL, original NAND, and any rebooter) When
-When
doing your wiring, you don't need an actual LPT cable, you can just feed the wires attatched to the console's motherboard into your PC's LPT port. And
-Most Importantly
, if you console is on the 2.0.8***.0 or newer dashboard, IT IS NOT JTAG-ABLE! Trying to JTAG it will only brick the flash controller, and render the console useless. (You won't be able to flash back original NAND)
-Make sure that you have two identical NAND dumps, and makedumps before flashing anything to the console.
-make
sure that you erase the flash ("nandpro lpt: -e400") before writing any image to it. (XeLL, original NAND, and any rebooter) When
-When
doing your wiring, you don't need an actual LPT cable, you can just feed the wires attatched to the console's motherboard into your PC's LPT port. And
-Most Importantly
, if you console is on the 2.0.8***.0 or newer dashboard, IT IS NOT JTAG-ABLE! Trying to JTAG it will only brick the flash controller, and render the console useless. (You won't be able to flash back original NAND)

Stato:

open

Modifica di: Chris Green ,

Testo:

There's aren't any great guides for JTAGing anywhere. The one that I used my first time was [http://www.se7ensins.com/forums/topic/108432-how-to-do-the-jtag-hackdump-nandxell/|This Guide] on Se7enSins. It will show you how to identify youtyour console, do the wiring, and flash XeLL, flashing a rebooter is the next step after doing that. You will also need [http://www.ebay.com/itm/100-Ohm-1-2-Watt-5-Carbon-Film-Resistors-35pcs-/190494300933?pt=LH_DefaultDomain_0&hash=item2c5a585b05|100 Ohm Resistors] (You have to buy them in bulk, but they're cheap) and [http://www.ebay.com/itm/1N4148-High-Speed-Switching-Diodes-100-pcs-/180597395202?pt=LH_DefaultDomain_0&hash=item2a0c718f02|1N4148 Diodes] (Also in bulk, but cheap) For the wiring, I recommend using non-braided (solid core) CAT5 wire. Good luck with your JTAG!
There's aren't any great guides for JTAGing anywhere. The one that I used my first time was [http://www.se7ensins.com/forums/topic/108432-how-to-do-the-jtag-hackdump-nandxell/|This Guide] on Se7enSins. It will show you how to identify youtyour console, do the wiring, and flash XeLL, flashing a rebooter is the next step after doing that. You will also need [http://www.ebay.com/itm/100-Ohm-1-2-Watt-5-Carbon-Film-Resistors-35pcs-/190494300933?pt=LH_DefaultDomain_0&hash=item2c5a585b05|100 Ohm Resistors] (You have to buy them in bulk, but they're cheap) and [http://www.ebay.com/itm/1N4148-High-Speed-Switching-Diodes-100-pcs-/180597395202?pt=LH_DefaultDomain_0&hash=item2a0c718f02|1N4148 Diodes] (Also in bulk, but cheap) For the wiring, I recommend using non-braided (solid core) CAT5 wire. Good luck with your JTAG!
 
Also, some advice:
 
-Make sure that you have two identical NAND dumps, and make sure that you erase the flash ("nandpro lpt: -e400") before writing any image to it. (XeLL, original NAND, and any rebooter) When doing your wiring, you don't need an actual LPT cable, you can just feed the wires attatched to the console's motherboard into your PC's LPT port. And, if you console is on the 2.0.8***.0 or newer dashboard, IT IS NOT JTAG-ABLE! Trying to JTAG it will only brick the flash controller, and render the console useless. (You won't be able to flash back original NAND)

Stato:

open

Modifica di: Chris Green ,

Testo:

There's aren't any great guides for JTAGing anywhere. The one that I used my first time was [http://www.se7ensins.com/forums/topic/108432-how-to-do-the-jtag-hackdump-nandxell/|This Guide] on Se7enSins. It will show you how to identify yout console, do the wiring, and flash XeLL, flashing a rebooter is the next step after doing that. You will also need [http://www.ebay.com/itm/100-Ohm-1-2-Watt-5-Carbon-Film-Resistors-35pcs-/190494300933?pt=LH_DefaultDomain_0&hash=item2c5a585b05|100 Ohm Resistors] (You have to buy them in bulk, but they're cheap) and [http://www.ebay.com/itm/1N4148-High-Speed-Switching-Diodes-100-pcs-/180597395202?pt=LH_DefaultDomain_0&hash=item2a0c718f02|1N4148 Diodes] (Also in bulk, but cheap) For the wiring, I recommend using non-braided (solid core) CAT5 wire. Good luck with your JTAG!
 
Also, some advice:
 
-Make sure that you have two identical NAND dumps, and make sure that you erase the flash ("nandpro lpt: -e400") before writing any image to it. (XeLL, original NAND, and any rebooter) AndWhen doing your wiring, you don't need an actual LPT cable, you can just feed the wires attatched to the console's motherboard into your PC's LPT port. And, if you console is on the 2.0.8***.0 or newer dashboard, IT IS NOT JTAG-ABLE! Trying to JTAG it will only brick the flash controller, and render the console useless. (You won't be able to flash back original NAND)
-Make sure that you have two identical NAND dumps, and make sure that you erase the flash ("nandpro lpt: -e400") before writing any image to it. (XeLL, original NAND, and any rebooter) AndWhen doing your wiring, you don't need an actual LPT cable, you can just feed the wires attatched to the console's motherboard into your PC's LPT port. And, if you console is on the 2.0.8***.0 or newer dashboard, IT IS NOT JTAG-ABLE! Trying to JTAG it will only brick the flash controller, and render the console useless. (You won't be able to flash back original NAND)

Stato:

open

Modifica di: Chris Green ,

Testo:

There's aren't any great guides for JTAGing anywhere. The one that I used my first time was [http://www.se7ensins.com/forums/topic/108432-how-to-do-the-jtag-hackdump-nandxell/|This Guide] on Se7enSins. It will show you how to identify yout console, do the wiring, and flash XeLL, flashing a rebooter is the next step after doing that. You will also need [http://www.ebay.com/itm/100-Ohm-1-2-Watt-5-Carbon-Film-Resistors-35pcs-/190494300933?pt=LH_DefaultDomain_0&hash=item2c5a585b05|100 Ohm Resistors] (You have to buy them in bulk, but they're cheap) and [http://www.ebay.com/itm/1N4148-High-Speed-Switching-Diodes-100-pcs-/180597395202?pt=LH_DefaultDomain_0&hash=item2a0c718f02|1N4148 Diodes] (Also in bulk, but cheap) For the wiring, I recommend using non-braided (solid core) CAT5CAT5 wire. Good luck with your JTAG!
There's aren't any great guides for JTAGing anywhere. The one that I used my first time was [http://www.se7ensins.com/forums/topic/108432-how-to-do-the-jtag-hackdump-nandxell/|This Guide] on Se7enSins. It will show you how to identify yout console, do the wiring, and flash XeLL, flashing a rebooter is the next step after doing that. You will also need [http://www.ebay.com/itm/100-Ohm-1-2-Watt-5-Carbon-Film-Resistors-35pcs-/190494300933?pt=LH_DefaultDomain_0&hash=item2c5a585b05|100 Ohm Resistors] (You have to buy them in bulk, but they're cheap) and [http://www.ebay.com/itm/1N4148-High-Speed-Switching-Diodes-100-pcs-/180597395202?pt=LH_DefaultDomain_0&hash=item2a0c718f02|1N4148 Diodes] (Also in bulk, but cheap) For the wiring, I recommend using non-braided (solid core) CAT5CAT5 wire. Good luck with your JTAG!
 
Also, some advice:
 
-Make sure that you have two identical NAND dumps, and make sure that you erase the flash ("nandpro lpt: -e400") before writing any image to it. (XeLL, original NAND, and any rebooter) And, if you console is on the 2.0.8***.0 or newer dashboard, IT IS NOT JTAG-ABLE! Trying to JTAG it will only brick the flash controller, and render the console useless. (You won't be able to flash back original NAND)

Stato:

open

Modifica di: Chris Green ,

Testo:

There's aren't any great guides for JTAGing anywhere. The one that I used my first time was [http://www.se7ensins.com/forums/topic/108432-how-to-do-the-jtag-hackdump-nandxell/|This Guide] on Se7enSins. It will show you how to identify yout console, do the wiring, and flash XeLL, flashing a rebooter is the next step after doing that. You will also need [http://www.ebay.com/itm/100-Ohm-1-2-Watt-5-Carbon-Film-Resistors-35pcs-/190494300933?pt=LH_DefaultDomain_0&hash=item2c5a585b05|100 Ohm Resistors] (You have to buy them in bulk, but they're cheap) and [http://www.ebay.com/itm/1N4148-High-Speed-Switching-Diodes-100-pcs-/180597395202?pt=LH_DefaultDomain_0&hash=item2a0c718f02|1N4148 Diodes] (Also in bulk, but cheap) For the wiring, I recommend using non-braided (solid core) CAT5. Good luck with your JTAG!
 
Also, some advice:
 
-Make sure that you have two identical NAND dumps, and make sure that you erase the flash ("nandpro lpt: -e400") before writing any image to it. (XeLL, original NAND, and any rebooter) And, if you console is on the 2.0.8***.0 or newer dashboard, IT IS NOT JTAG-ABLE! Trying to JTAG it will only brick the flash controller, and render the console useless. (You won't be able to flash back original NAND)
-Make sure that you have two identical NAND dumps, and make sure that you erase the flash ("nandpro lpt: -e400") before writing any image to it. (XeLL, original NAND, and any rebooter) And, if you console is on the 2.0.8***.0 or newer dashboard, IT IS NOT JTAG-ABLE! Trying to JTAG it will only brick the flash controller, and render the console useless. (You won't be able to flash back original NAND)

Stato:

open

Post originale di: Chris Green ,

Testo:

There's aren't any great guides for JTAGing anywhere.  The one that I used my first time was [http://www.se7ensins.com/forums/topic/108432-how-to-do-the-jtag-hackdump-nandxell/|This Guide] on Se7enSins.  It will show you how to identify yout console, do the wiring, and flash XeLL, flashing a rebooter is the next step after doing that.  You will also need [http://www.ebay.com/itm/100-Ohm-1-2-Watt-5-Carbon-Film-Resistors-35pcs-/190494300933?pt=LH_DefaultDomain_0&hash=item2c5a585b05|100 Ohm Resistors] (You have to buy them in bulk, but they're cheap) and [http://www.ebay.com/itm/1N4148-High-Speed-Switching-Diodes-100-pcs-/180597395202?pt=LH_DefaultDomain_0&hash=item2a0c718f02|1N4148 Diodes] (Also in bulk, but cheap)  For the wiring, I recommend using non-braided (solid core) CAT5.  Good luck with your JTAG!

Also, some advice:

-Make sure that you have two identical NAND dumps, and make sure that you erase the flash ("nandpro lpt: -e400") before writing any image to it. (XeLL, original NAND, and any rebooter)

Stato:

open