Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Store

Aiuto

Versione corrente di: jayeff ,

Testo:

Hi @ Ramansingh Manhar,
 
Did you mean a Motorola E6s?
 
''First '''do not turn on your phone''' and then you need to '''remove the battery as soon as possible''' from the phone'' to minimize any further damage.
 
Then you need to dis-assemble the rest of the phone and clean ''all the affected parts'' using '''Isopropyl Alcohol 99%+''' (available from electronics parts stores) to ''remove all traces of corrosion and water''. Do not use "rubbing alcohol" as in some cases this is only 70% IPA or less, can contain scents and is not as effective. If you have to use it, check the label to verify the amount of IPA it contains. The morehigher % IPA the better.
Then you need to dis-assemble the rest of the phone and clean ''all the affected parts'' using '''Isopropyl Alcohol 99%+''' (available from electronics parts stores) to ''remove all traces of corrosion and water''. Do not use "rubbing alcohol" as in some cases this is only 70% IPA or less, can contain scents and is not as effective. If you have to use it, check the label to verify the amount of IPA it contains. The morehigher % IPA the better.
 
Here is a link that describes the process.
 
[[Electronics Water Damage]]
 
Also be sure to remove the LCD screen flex cable from its connector on the systemboard and clean the cable end and the connector with IPA in case water got in there as well.
 
As always with electronics, especially surface mounted pcb be gentle when handling and especially when brushing away the corrosion. You do not want to remove any components from the board.
 
Hopefully after you have done all this the phone ''might'' possibly work correctly again.
 
I cannot find a dis-assembly guide for your model phone. [https://www.youtube.com/watch?v=kLdTSyToG7U|Here’s] one for a Motorola E5 which hopefully may be close enough to be of some help.
 
If this process seems too daunting, take your phone to a reputable, professional phone repair service, experienced in liquid damage repair and ask for a quote for a repair. If you decide to do this, ''do it sooner than later''.

Stato:

open

Post originale di: jayeff ,

Testo:

Hi @ Ramansingh Manhar,

Did you mean a Motorola E6s?

''First '''do not turn on your phone''' and then you need to '''remove the battery as soon as possible''' from the phone'' to minimize any further damage.

Then you need to dis-assemble the rest of the phone and  clean ''all the affected parts'' using '''Isopropyl Alcohol 99%+''' (available from electronics parts stores) to ''remove all traces of corrosion and water''. Do not use "rubbing alcohol" as in some cases this is only 70% IPA or less, can contain scents and is not as effective. If you have to use it, check the label to verify the amount of IPA it contains. The more the better.

Here is a link that describes the process.

[[Electronics Water Damage]]

Also be sure to remove the LCD screen flex cable from its connector on the systemboard and clean the cable end and the connector with IPA in case water got in there as well.

As always with electronics, especially surface mounted pcb be gentle when handling and especially when brushing away the corrosion. You do not want to remove any components from the board.

Hopefully after you have done all this the phone ''might'' possibly work correctly again.

I cannot find a dis-assembly guide for your model phone. [https://www.youtube.com/watch?v=kLdTSyToG7U|Here’s] one for a Motorola E5  which hopefully may be close enough to be of some help.

If this process seems too daunting, take your phone to a reputable, professional phone repair service, experienced in liquid damage repair and ask for a quote for a repair. If you decide to do this, ''do it sooner than later''.

Stato:

open