Aggiusta le tue cose Community Store
Aiuto

Versione corrente di: Jack Applegate

Testo:

Replacing Broken Screen
Removing Cover
-1. Dislodging cover
+1. Dislodging cover
-• Take tablet and rotate on its side, so that the two screws are facing upward.
-• Use 1mm Phillips screwdriver to and insert into screw hold on the left side of the tablet.
-• Rotate screwdriver counterclockwise to remove screw from its port.
-• Follow steps 2 and 3 to remove second screw on right side of tablet. (Both set screws will be removed from device)
-• With screws removed, insert plastic prying tool and pry back case away from the device slowly moving the plastic prying tool along the device. (Case should easily dislodge from tablet.
+• Take tablet and rotate on its side, so that the two screws are facing upward.
-2. Remove speaker from cover
+• Use 1mm Phillips screwdriver to and insert into screw hold on the left side of the tablet.
-• Hold positive and negative wires as close as possible to the speaker.
-• Use plastic prying tool and fingers to simultaneously lift speaker from cover. (All connections from cover to tablet are removed)
-• Set cover aside.
+• Rotate screwdriver counterclockwise to remove screw from its port.
+• Follow steps 2 and 3 to remove second screw on right side of tablet. (Both set screws will be removed from device)
+• With screws removed, insert plastic prying tool and pry back case away from the device slowly moving the plastic prying tool along the device. (Case should easily dislodge from tablet.
+
+2. Remove speaker from cover
+
+• Hold positive and negative wires as close as possible to the speaker.
+
+• Use plastic prying tool and fingers to simultaneously lift speaker from cover. (All connections from cover to tablet are removed)
+
+• Set cover aside.
Removing Battery from Device
-1. Locating battery
+1. Locating battery
-• To locate the battery, look to the left upper-hand corner, and find the silver rectangle taking up 3/4 of the tablet
+• To locate the battery, look to the left upper-hand corner, and find the silver rectangle taking up 3/4 of the tablet
-2. Removing battery
+2. Removing battery
-• Insert plastic prying tool under upper-hand corner of battery and slide back and forth
-• Once loosened, insert plastic prying tool under lower-hand corner and repeat sliding action
-• Repeat previous steps until battery comes loose from device
+• Insert plastic prying tool under upper-hand corner of battery and slide back and forth
+
+• Once loosened, insert plastic prying tool under lower-hand corner and repeat sliding action
+
+• Repeat previous steps until battery comes loose from device
[If prying tool is unsuccessful, use fingers to grasp edges of device and pull upward]
-
Removing Motherboard
-5. Detaching electrical ribbons
+5. Detaching electrical ribbons
-• Grip the ribbon located at the far end of the circuit board with a plastic spudger tool
-• Put pressure on the connector until the clasp comes undone
-• Gently pull up on electrical ribbon until it disconnects from circuit board
-• Repeat these steps to remove the second electrical ribbon from the motherboard
+• Grip the ribbon located at the far end of the circuit board with a plastic spudger tool
-6. Removing screws connecting motherboard
+• Put pressure on the connector until the clasp comes undone
-• Using 1mm Phillips screwdriver, insert into screw hole on motherboard at rotate counterclockwise (This should remove screw from motherboard)
-• Repeat this step for the remaining three screws connecting the motherboard to the device
+• Gently pull up on electrical ribbon until it disconnects from circuit board
-7. Removing Wi-Fi connector
-
-• With fingers, grip the green Wi-Fi connector
-• Gently pull up on connector to remove tape holding the connector in place
+• Repeat these steps to remove the second electrical ribbon from the motherboard
+6. Removing screws connecting motherboard
-8. Dislodging Motherboard
+• Using 1mm Phillips screwdriver, insert into screw hole on motherboard at rotate counterclockwise (This should remove screw from motherboard)
-• Using your fingers, gently lift the motherboard
+• Repeat this step for the remaining three screws connecting the motherboard to the device
+
+7. Removing Wi-Fi connector
+
+• With fingers, grip the green Wi-Fi connector
+
+• Gently pull up on connector to remove tape holding the connector in place
+
+8. Dislodging Motherboard
+
+• Using your fingers, gently lift the motherboard
[If motherboard does not remove easily, make sure that all the screws have been disconnected and all electrical ribbons have been detached]
-
Separating Screen from Glass
-1. Removing glass
+1. Removing glass
-• Insert plastic prying tool under screen and exert pressure, pulling upward
-• Repeat this step around each corner of the screen until if pops off (this will separate the screen from the glass)
+• Insert plastic prying tool under screen and exert pressure, pulling upward
-2. Removing electrical film
+• Repeat this step around each corner of the screen until if pops off (this will separate the screen from the glass)
-• Place heating pad on glass frame in order to loosen adhesive for 3 to 5 minutes
+2. Removing electrical film
-[If adhesive does not loosen, set on heating pad for 5-7 more minutes]
+• Place heating pad on glass frame in order to loosen adhesive for 3 to 5 minutes
-• Remove plastic film from glass frame (This will allow you to install new glass)
+[If adhesive does not loosen, set on heating pad for 5-7 more minutes]
+
+• Remove plastic film from glass frame (This will allow you to install new glass)
+
+
+[https://www.ifixit.com/Wiki/4Sight_9_Troubleshooting#Section_Broken_Improper_fitting_screen|For more information, try using the troubleshooting page]

Stato:

open

Modifica di: Jack Applegate

Testo:

-o Some users have claimed, “half as thin as other tablets”
+Replacing Broken Screen
-o Recommended fix is to replace the screen
+Removing Cover
-o Alternate fix would be to copy files onto a micro-USB and upload on another tablet
+1. Dislodging cover
+
+• Take tablet and rotate on its side, so that the two screws are facing upward.
+• Use 1mm Phillips screwdriver to and insert into screw hold on the left side of the tablet.
+• Rotate screwdriver counterclockwise to remove screw from its port.
+• Follow steps 2 and 3 to remove second screw on right side of tablet. (Both set screws will be removed from device)
+• With screws removed, insert plastic prying tool and pry back case away from the device slowly moving the plastic prying tool along the device. (Case should easily dislodge from tablet.
+
+2. Remove speaker from cover
+
+• Hold positive and negative wires as close as possible to the speaker.
+• Use plastic prying tool and fingers to simultaneously lift speaker from cover. (All connections from cover to tablet are removed)
+• Set cover aside.
+
+
+
+Removing Battery from Device
+
+1. Locating battery
+
+• To locate the battery, look to the left upper-hand corner, and find the silver rectangle taking up 3/4 of the tablet
+
+2. Removing battery
+
+• Insert plastic prying tool under upper-hand corner of battery and slide back and forth
+• Once loosened, insert plastic prying tool under lower-hand corner and repeat sliding action
+• Repeat previous steps until battery comes loose from device
+
+[If prying tool is unsuccessful, use fingers to grasp edges of device and pull upward]
+
+
+Removing Motherboard
+
+5. Detaching electrical ribbons
+
+• Grip the ribbon located at the far end of the circuit board with a plastic spudger tool
+• Put pressure on the connector until the clasp comes undone
+• Gently pull up on electrical ribbon until it disconnects from circuit board
+• Repeat these steps to remove the second electrical ribbon from the motherboard
+
+6. Removing screws connecting motherboard
+
+• Using 1mm Phillips screwdriver, insert into screw hole on motherboard at rotate counterclockwise (This should remove screw from motherboard)
+• Repeat this step for the remaining three screws connecting the motherboard to the device
+
+7. Removing Wi-Fi connector
+
+• With fingers, grip the green Wi-Fi connector
+• Gently pull up on connector to remove tape holding the connector in place
+
+
+8. Dislodging Motherboard
+
+• Using your fingers, gently lift the motherboard
+
+[If motherboard does not remove easily, make sure that all the screws have been disconnected and all electrical ribbons have been detached]
+
+
+Separating Screen from Glass
+
+1. Removing glass
+
+• Insert plastic prying tool under screen and exert pressure, pulling upward
+• Repeat this step around each corner of the screen until if pops off (this will separate the screen from the glass)
+
+2. Removing electrical film
+
+• Place heating pad on glass frame in order to loosen adhesive for 3 to 5 minutes
+
+[If adhesive does not loosen, set on heating pad for 5-7 more minutes]
+
+• Remove plastic film from glass frame (This will allow you to install new glass)

Stato:

open

Post originale di: Jack Applegate

Testo:

o    Some users have claimed, “half as thin as other tablets”

o    Recommended fix is to replace the screen

o    Alternate fix would be to copy files onto a micro-USB and upload on another tablet

Stato:

open