Introduzione

Rimozione del pannello di vetro anteriore per accedere al display e al resto dei componenti interni dell'iMac.

Parti

Nessuna parte richiesta.

Far aderire una ventosa accanto a ciascuno dei due angoli superiori del pannello di vetro. Per far aderire le ventose, per prima cosa posizionarle con la maniglia semovente parallela alla superficie del pannello di vetro (come evidenziato nella prima e nella seconda immagine). Tenendo delicatamente la ventosa contro il vetro, sollevare la maniglia semovente finché non è parallela all'altra maniglia (come evidenziato nella terza immagine).
  • Far aderire una ventosa accanto a ciascuno dei due angoli superiori del pannello di vetro.

  • Per far aderire le ventose, per prima cosa posizionarle con la maniglia semovente parallela alla superficie del pannello di vetro (come evidenziato nella prima e nella seconda immagine).

  • Tenendo delicatamente la ventosa contro il vetro, sollevare la maniglia semovente finché non è parallela all'altra maniglia (come evidenziato nella terza immagine).

  • Se la ventosa non aderisce, provare a ripulire il pannello di vetro e la ventosa con un solvente delicato.

  • Do not use the suction cups to carry the display glass because if one of them fails to stick, you could drop the screen and break it.

  • The original iMac box makes a good place to store the glass panel. Otherwise, a padded horizontal surface, like a towel on a desk will do nicely.

You can easily lift the glass panel off the magnets with only your fingernails (or something thin like a credit card or a guitar pick). No need to buy suction cups you will only use once.

Nick Caron - Replica

Yes, you don't need the specific suction cups to remove the display cover - it's held on by magnets, and if you start at the center by the iSight you can work out to the edges and remove it. I had an iPhone screen suction cup around and it helped with balancing the screen when you pull it out fully, but by no ways is it required.

jtowner - Replica

Great guide and pretty straight forward the only thing that took me ages and I didn't manage to undo were the power btn cable (step 28) and the thermal sensor (step 25) Seemed like they were glued on! Very difficult to remove and obviously conscious so I didn't break anything!

Eddie - Replica

Thanks!!! Worked excellently.

I used a plunger (clean first ;-) to get the screen off, and http://exirion.net/ssdfanctrl/ for fan control.

Then, i did not take out the whole display and left it in the hinges on the bottom side and held it up with two small cardboard boxes. Easy enough to disconnect the hdd then.

I replaced with an ssd, put that into a ssd enclosure. Had to drill an extra hole in it to fasten the pins that hold it in place.

Used Carbon Copy Cloner to make an image from the old hdd, with the sad connected via usb. Checked it of it booted via System Preferences > Startup Disk. It worked so the took the imac apart and replaced the disk. Booted, everything was working as always, only faster!

Frank303 - Replica

I'm replacing my optical drive too. what exactly needs to be plugged into the SSD? I don't have the kit - as I am not sure one is required if I buy something like this: http://www.amazon.com/gp/product/B0056OB...

Can you please advise? Can I do it with this piece, or do I need to get the entire bracket kit?

Allen Borza -

My display data cable forks, with a smaller section going up near the camera board. Where it forks, it is attached to the aluminum plate that attaches around the cpu board. I haven't seen any images that look similar, and I'm stumped at how to remove this second section of the cable. 2010 i7 build to order

Awolf - Replica

Agree with the other comments here. Despite buying suction cups, not sure they were necessary as the screen removed very easily. A sat nav suction cup would do the job fine.

Stuart Bloomfield - Replica

I can confirm that it is possible to remove the front glass using fingernails rather than suction cups. It isn’t easy, but if you try you should be able to pry off the glass.

I did this twice: once at the beginning of the procedure and once again at the end, when I realized that a big pice of lint was trapped under the glass.

gordonhamachi - Replica

Kit RAM Mac
Accelera il Mac. Porta la memoria al massimo.
Kit RAM Mac
Metti più memoria nel tuo Mac.
Sollevare il pannello di vetro in perpendicolare rispetto alla superficie dello schermo LCD, affinché sia possibile sgombrare i piedini di montaggio in acciaio inseriti lungo il lato sottostante al bordo superiore del pannello di vetro. Estrarre il panello di vetro dal bordo inferiore dell'iMac e riporlo da parte con attenzione. Durante la reinstallazione, pulire con attenzione la parte interna del pannello di vetro e la superficie dello schermo LCD, poiché la polvere e le impronte digitali saranno sgradevolmente visibili durante l'utilizzo della macchina.
  • Sollevare il pannello di vetro in perpendicolare rispetto alla superficie dello schermo LCD, affinché sia possibile sgombrare i piedini di montaggio in acciaio inseriti lungo il lato sottostante al bordo superiore del pannello di vetro.

  • Estrarre il panello di vetro dal bordo inferiore dell'iMac e riporlo da parte con attenzione.

  • Durante la reinstallazione, pulire con attenzione la parte interna del pannello di vetro e la superficie dello schermo LCD, poiché la polvere e le impronte digitali saranno sgradevolmente visibili durante l'utilizzo della macchina.

you should do this mac up, because, for me, one of the suction cup failed, and the glass fall into the lcd screen. Now there is a big hole in it...

Lau - Replica

do you still have this panel?

Alpha Dimension -

Reassembly: After powering on and running for a few minutes, found a large whitish patch on the screen. Persists after powerdown.

Turned out to be condensation, though it didn't look like it - more like fine white powder rubbed in. Humidity is very high this time of the year. Fix: start airconditioner in a room, leave it running a while, take iMac in, prise open the glass again. Condensation vanishes instantly. Keep it out for a ~15 minutes running infinite loops to get iMac nicely heated up and fans running. Snap glass back.

ganesh - Replica

I used a Swiffer dry cloth to get all the dust off the screen while just blowing with my mouth at a steep angle. I know I didn't get every speck, but the screen looks perfect once assembled and lit again. Removing the glass from the screen is pretty easy if you need to re-clean it.

Jay Gillibrand - Replica

I used a microfiber cloth instead, which worked well. The same type as yo use to clean eye glasses, but in a larger form factor.

Daniel -

The Swiffer idea worked great! I just brush it over the LCD and glass panel lightly, and all dust particles are gone quickly. The screen after boot up looked beautiful. Thanks!

dtsai2 -

I strongly recomment to detach the suction cups while working at the rest of the steps. In my case after half an our i heart a crack noise behind me on the table... The vacuum of one of the suction cups braked the glass! maybe there should be a warning in the Repair guide

shippe - Replica

I didn't crack the screen, but it popped out of the shims and then popped back in, as if the glass edge is magnetic or has steel in it to connect to magnets. Be careful with this step — it is pretty nerve-wracking, but doable!

Alex Reynolds - Replica

You need a big clean surface free, or at least 2 or more free surfaces because the iMac, the glass and the LCD display are quite bulky. You'll also probably need space for a tablet or a laptop to read this guide while you are working. And don't forget room to work on the optical unit and for the tools you are going to use. I covered a large table with a double layer of bubble wrap. In my opinion it's better to put the glass face down to limit powder sticking on the internal surface.

Roberto Blandino - Replica

Thanks good advice! I was wondering exactly about the working space issue!

matteoslataper -

I am doing this repair now. After successfully lifting off the glass panel (yay!), dust blew out of the lower open edge. So I sprayed a can of air around edges. But a poof of the “air” condensated on the LCD. Does anyone know if I can clean the LCD same as how the glass is cleaned (damp cloth with equal parts white distilled vinegar/distilled water) and if not then how?

Amy C - Replica

Hi Amy,

To clean the LCD panel, I would suggest using a clean microfiber cloth and rubbing alcohol. Distilled water can be used, but avoid regular water, which contains minerals. Make sure the microfiber cloth is absolutely clean and has no hard particles sticking on the surface, which will scratch your LCD when you wipe it.

Wet the surface with some alcohol and gently wipe with the microfiber cloth. Wipe in one direction.

Arthur Shi -

Conclusione

Per riassemblare il dispositivo, seguire queste istruzioni in ordine inverso.

Altre 26 persone hanno completato questa guida.

Un ringraziamento speciale a questi traduttori:

85%

Nina Steinhaeuser ci sta aiutando ad aggiustare il mondo! Vuoi partecipare?
Inizia a tradurre ›

Your topic says "Replacement" not "Removal". There is nothing here about how to obtain a new glass panel and how to install it.

rjlong65 - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 4

Ultimi 7 Giorni: 52

Ultimi 30 Giorni: 230

Tutti i Tempi: 92,922