Introduzione

Utilizzare questa guida per sostituire un pannello di vetro anteriore danneggiato.

Prima di iniziare, scollegare l'iMac dall'alimentazione e poggiarlo su una superficie morbida come indicato. Far aderire una ventosa accanto a ciascuno dei due angoli superiori del pannello di vetro.
  • Prima di iniziare, scollegare l'iMac dall'alimentazione e poggiarlo su una superficie morbida come indicato.

  • Far aderire una ventosa accanto a ciascuno dei due angoli superiori del pannello di vetro.

  • Per far aderire le nostre ventose, per prima cosa posizionarle con la maniglia semovente parallela alla superficie del pannello di vetro. Tenendo delicatamente la ventosa contro il vetro, sollevare la maniglia semovente finché non è parallela all'altra maniglia.

  • Se la ventosa non aderisce, provare a ripulire il pannello di vetro e la ventosa con un solvente delicato.

Change "Before beginning, unplug your iMac and lay it on a soft surface as shown." to "Lay your iMac on a soft surface as shown"

Henry Barnett - Replica

my imac power sullye not powering

tahir - Replica

imac 2544 2.5 core i5 i touched the motherboard to supply and it spark now it is not powering

please tell me the directions

thanks witting for answering .

tahir - Replica

Im sorry to say, If it sparked when you touched it your motherboard s now fried. You need a new one.

Robert Wacker -

Very easy to lift the glass out. Don't jerk too hard.

kctipton - Replica

Success replacing the stock ST31000528AS with a STBD3000100 (Dead 1TB to new 3TB, both Seagate). First try. Using another Mac and a quality Firewire 800 cable, I formatted it using Target Disk mode, 2 partitions (defaults, except I made the first one bigger than the second). To the second, smaller one, I copied a bootable Install OS X Mavericks partition. Tried to boot. It booted, and I installed; nary a glitch. (Running the Installer over Firewire would have been faster, but I didn't want to reboot this machine.)

See part 2 below...

Matthew Elvey - Replica

(Part 2:)

I SKIPPED steps 6, 7 AND 8! Instead, after doing Step 5, I noticed I then had enough room and cable length to access the screws in Step 11 if I lifted the LCD up an inch or so, rotated it about 20-30 degrees clockwise and moved it a couple inches toward the base, and put it down. After removing them (Step 11), I propped up the LCD (with a spare spudger) and had enough room to do Steps 12, 13, and 14 without much difficulty. Felt safer/less work and risk than not skipping steps 6-8. No risk of the damage Ersan and Michael caused performing Step 7!

Matthew Elvey -

I just edited that step to add a note about the shortcut.

Matthew Elvey -

What the ???

Geoff Wacker has REJECTED my edit: https://www.ifixit.com/Guide/history/ste...

I wonder why. What's the deal, Geoff? I mean I'd understand if I suggested folks didn't need the suction cups, as that could cut into iFixit's income stream, but what's wrong with suggesting that a few steps aren't needed? It worked for me; the EMC 2389 I fixed is humming along with a new 3TB HD I installed while skipping those steps.

Matthew Elvey -

I did not have to remove a single cable! After undoing the torx screws from the sides, I was able to rotate the LCD out of the way enough to reach all the screws holding in the ODD bracket. One of them was a bit challenging to get to, but I never felt that I was risking the cables by leaving them connected. Also, it wasn't totally clear, but you have to actually remove the ODD itself from the ODD bracket - 4 torx screws. The SDD mounts into the hard drive enclosure, then the enclosure is screwed into the bracket. Those holes (enclosure <-> Bracket) did not line up correctly for me, and I had to go with only three of them connected in the end. Seems to work fine.

cdansmith1 - Replica

Another comment on DATA & LCD Temp. Sensor cables: I had to remove the vertical sync, and the backlight cable, however, if you have an assistant or/can carefully rotate the screen clockwise/and then have it held up about 5" to 6" at a slight angle, you do not need to remove LCD data cable or LCD thermal cable, however - IMPORTANT: you must have a second pair of hands/or way to securely prop up the LCD. Also, don't rotate too much, since then you will pull out LCD data cable, and it renders the whole exercise moot, or can damage the cable or connector.

MaximBorzov - Replica

You don't need suction cups. The screen, held by magnets, can simply be pried off using a very thin blade such as a screw driver and fingers.

Deepsurvival - Replica

That's a bad idea. using a metal tool to pry off glass is likely to end with an expensive broken front glass.

Suction cups are common. Find a couple and do it the safe way. I use some cheap ones that came with iPhone repair kit.

max damage -

Hello, I just need to replace a slightly cracked screen on my iMac. Where is it best to place the suction cups? Thanks in advance

michelemiller0 - Replica

No need for suction cups, I just stuck my nails (short like guys usually have) between the top part of the screen and body, and it came off easily. I've never done it before, so it seems to be very easy.

Nikolas Lintulaakso - Replica

Nails worked for me too

Rob Dale - Replica

Just completed the replacement of the optical drive with an SSD using an OWC Data Doubler kit. Attempted to remove the optical drive without disconnecting any cables but found it a bit fiddly to orient the screen for good access. I bit the bullet and disconnected them and found the process less daunting than I imagined. Reconnecting them was similarly straightforward if you're careful.

Tip: you can skip the step for removing the optical drive thermal sensor connector from the motherboard. Still need to remove the sensor from the optical drive but you can leave that hanging and reattach it to the SSD later.

osienna - Replica

I have an odd question -- I want to remove the polarizer from the LCD. With some monitors this is trivial, others not so much. My question is whether it is bonded to the Liquid crystal, or whether it's loose, or cutting it with a razor blade would remove it. Obviously I'd like to know before I go to the trouble of dismantling the thing... Thanks. Paul

Paul Kwiat - Replica

I use Garmin GPS suction cup. Work very well

jc3Dcx - Replica

I used a plumber's helper (you know, the thing you use for a clogged toilet

Kai-U. Köhler - Replica

Kit RAM Mac
Accelera il Mac. Porta la memoria al massimo.
Kit RAM Mac
Metti più memoria nel tuo Mac.
Sollevare il pannello di vetro in perpendicolare rispetto alla superficie dello schermo LCD, affinché sia possibile sgombrare i piedini di montaggio in acciaio inseriti lungo il lato sottostante al bordo superiore del pannello di vetro. Estrarre il panello di vetro dal bordo inferiore dell'iMac e riporlo da parte con attenzione.
  • Sollevare il pannello di vetro in perpendicolare rispetto alla superficie dello schermo LCD, affinché sia possibile sgombrare i piedini di montaggio in acciaio inseriti lungo il lato sottostante al bordo superiore del pannello di vetro.

  • Estrarre il panello di vetro dal bordo inferiore dell'iMac e riporlo da parte con attenzione.

  • Durante la reinstallazione, pulire con attenzione la parte interna del pannello di vetro e la superficie dello schermo LCD, poiché la polvere e le impronte digitali saranno sgradevolmente visibili durante l'utilizzo della macchina.

What's the best product to clean the face of the LCD?

Steve Speirs - Replica

Microfiber Cloth

Leonardo Fournier -

Conclusione

Per riassemblare il dispositivo, seguire queste istruzioni in ordine inverso.

Altre 25 persone hanno completato questa guida.

Un ringraziamento speciale a questi traduttori:

100%

Oriane Petit ci sta aiutando ad aggiustare il mondo! Vuoi partecipare?
Inizia a tradurre ›

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 53

Ultimi 30 Giorni: 196

Tutti i Tempi: 46,057