Introduzione

Dissembly to replace/repair optical drive.

Unplug all the cables from the computer, including the power cable. Lay the computer face-down, supporting the neck and base with a soft cloth under the screen.
  • Unplug all the cables from the computer, including the power cable. Lay the computer face-down, supporting the neck and base with a soft cloth under the screen.

Aggiungi Commento

Loosen the four Phillips #0 screws.
  • Loosen the four Phillips #0 screws.

Aggiungi Commento

Carefully remove the base access panel.
  • Carefully remove the base access panel.

Aggiungi Commento

Remove the four 25mm T-15 screws. Remove the four 25mm T-15 screws.
  • Remove the four 25mm T-15 screws.

Aggiungi Commento

Open the housing plate. Be gentle with the wires still connected to the logic board  so as not to ruin the cables.
  • Open the housing plate.

  • Be gentle with the wires still connected to the logic board so as not to ruin the cables.

  • A fixed plug connector between the logic board and upper unit will cause some resistance. Pull gently but firmly.

Aggiungi Commento

Remove the 2 torx 10mm screws on the EMI shield Carefully remove shield and copper tape Carefully remove shield and copper tape
  • Remove the 2 torx 10mm screws on the EMI shield

  • Carefully remove shield and copper tape

Aggiungi Commento

Remove the 4 10mm torx screws attatched to the drive carrier. The drive carrier includes optical drive and hard drive.
  • Remove the 4 10mm torx screws attatched to the drive carrier.

  • The drive carrier includes optical drive and hard drive.

Aggiungi Commento

Grasp the carrier with both hands on each side.
  • Grasp the carrier with both hands on each side.

  • Remove the carrier by lifting up and out.

  • Pull gently but firmly. The carrier is meant to fit snugly.

Aggiungi Commento

Flip the removed carrier to the right and pull out power cables.
  • Flip the removed carrier to the right and pull out power cables.

Aggiungi Commento

Peel back the white paper, revealing the screws that connect the hard drive to the carrier. Remove the 4 T-10 5mm screws connecting the hard drive and frame. (There are 2 screws on each side) Remove the 4 T-10 5mm screws connecting the hard drive and frame. (There are 2 screws on each side)
  • Peel back the white paper, revealing the screws that connect the hard drive to the carrier.

  • Remove the 4 T-10 5mm screws connecting the hard drive and frame. (There are 2 screws on each side)

Aggiungi Commento

Slide the hard drive out from the frame and optical drive.
  • Slide the hard drive out from the frame and optical drive.

Aggiungi Commento

Remove the four T-10 6mm screws at the sides of the drive.
  • Remove the four T-10 6mm screws at the sides of the drive.

Aggiungi Commento

Slide the optical drive out of the carrier
  • Slide the optical drive out of the carrier

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 5 persone hanno completato questa guida.

Courtney

Membro da: 06/10/2011

734 Reputazione

3 Guide realizzate

Team

Cal Poly, Team 21-22, Maness Fall 2011 Membro di Cal Poly, Team 21-22, Maness Fall 2011

CPSU-MANESS-F11S21G22

4 Membri

13 Guide realizzate

Should step ten of removing the optical drive be broken into two different steps

David Hunter - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 5

Ultimi 30 Giorni: 15

Tutti i Tempi: 3,039