Introduzione

Learn to remove and replace the main circuit board in your keyboard with this guide. The process is moderately involved and requires the removal of many screws and light force for some parts.

Turn the keyboard over so that the keys are facing the ground.
  • Turn the keyboard over so that the keys are facing the ground.

Aggiungi Commento

Pop the tabs on the battery casing and remove it from the back plate.
  • Pop the tabs on the battery casing and remove it from the back plate.

Aggiungi Commento

Locate the six batteries and remove them from the battery cavity.
  • Locate the six batteries and remove them from the battery cavity.

what type of batteries? and how much ?

thanks godbless

colladonelson - Replica

Remove the six 10mm screws at the top of the backplate.
  • Remove the six 10mm screws at the top of the backplate.

Aggiungi Commento

Remove the seven 12mm screws in the middle of the back plate.
  • Remove the seven 12mm screws in the middle of the back plate.

Aggiungi Commento

Kit RAM Mac
Accelera il Mac. Porta la memoria al massimo.
Kit RAM Mac
Metti più memoria nel tuo Mac.
Remove the eight 10mm screws from the side and the bottom of the back plate.
  • Remove the eight 10mm screws from the side and the bottom of the back plate.

Aggiungi Commento

As the face plate is no longer connected to the body of the keyboard, be careful to not drop the body when performing this step.
  • As the face plate is no longer connected to the body of the keyboard, be careful to not drop the body when performing this step.

  • Flip over the keyboard

Aggiungi Commento

Lifting from the front and the back of the face plate equally, pull the face plate up and then back, away from the keyboard. Be careful when removing the face plate. There are wires attached.
  • Lifting from the front and the back of the face plate equally, pull the face plate up and then back, away from the keyboard.

    • Be careful when removing the face plate. There are wires attached.

Aggiungi Commento

Locate the main circuit board - it should be toward the middle of the detached face plate.
  • Locate the main circuit board - it should be toward the middle of the detached face plate.

Aggiungi Commento

Use a plastic opening tool or spudger to carefully pry up the beige ribbon connectors and remove the wires from them. Be sure to use a tool that is ESD safe!
  • Use a plastic opening tool or spudger to carefully pry up the beige ribbon connectors and remove the wires from them.

    • Be sure to use a tool that is ESD safe!

    • Use a slightly upward force as parallel to the ground as possible.

    • Be sure to make a mental note or jot down the locations of the specific ribbon cables. Some are in close proximity to each other and it can be easy to forget which ribbon goes where.

  • Be sure to unplug the smaller ribbon that connects to a different circuit board.

  • Take care not to use too much force. The connectors are fragile, the ribbon wires are easily bent, and too much force may damage the circuit board if you happen to miss.

Aggiungi Commento

Move the ribbons out of the way and remove the eight 10mms crews in the middle that hold the circuit board down.
  • Move the ribbons out of the way and remove the eight 10mms crews in the middle that hold the circuit board down.

  • Remove the two 12mm screws in the corner of the circuit board.

Aggiungi Commento

Remove this wire carefully by hand.
  • Remove this wire carefully by hand.

Aggiungi Commento

Completely remove the circuit board from the face plate.
  • Completely remove the circuit board from the face plate.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 7 persone hanno completato questa guida.

Team

Cal Poly, Team 2-62, Propen Fall 2012 Membro di Cal Poly, Team 2-62, Propen Fall 2012

CPSU-PROPEN-F12S2G62

2 Membri

6 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 19

Ultimi 30 Giorni: 71

Tutti i Tempi: 4,939