Introduzione

Use this guide to remove the Connex Vital Signs Monitor from the Welch Allen office cart stand.

PLEASE NOTE: This repair guide was developed by the iFixit team based on Welch Allyn's own service manual. Neither iFixit nor this repair guide is endorsed by or affiliated with Welch Allyn.

Parti

Nessuna parte richiesta.

Unplug the AC power connection cable. Unplug the AC power connection cable.
  • Unplug the AC power connection cable.

Aggiungi Commento

Place your thumb and forefinger on the blood pressure (NIBP) hose connector. Squeeze the side tabs until the connector releases. Always grasp the hose by the connector. Do not pull on the hose itself. Pull the connector away from the connector port.
  • Place your thumb and forefinger on the blood pressure (NIBP) hose connector. Squeeze the side tabs until the connector releases.

    • Always grasp the hose by the connector. Do not pull on the hose itself.

  • Pull the connector away from the connector port.

Aggiungi Commento

Place your thumb and forefinger on the Pulse oximetry (SpO2 or combined SpO2/SpHb) cable connector. Squeeze the side tabs until the connector releases. Always grasp the cable by the connector. Do not pull on the cable itself. Pull the connector away from the connector port.
  • Place your thumb and forefinger on the Pulse oximetry (SpO2 or combined SpO2/SpHb) cable connector. Squeeze the side tabs until the connector releases.

    • Always grasp the cable by the connector. Do not pull on the cable itself.

  • Pull the connector away from the connector port.

Aggiungi Commento

Grasp the temperature probe and pull it up to remove it from the monitor. Grasp the temperature probe and pull it up to remove it from the monitor.
  • Grasp the temperature probe and pull it up to remove it from the monitor.

Aggiungi Commento

Remove the cover of the temperature module by pressing the tab and sliding the cover to the right. Remove the cover of the temperature module by pressing the tab and sliding the cover to the right. Remove the cover of the temperature module by pressing the tab and sliding the cover to the right.
  • Remove the cover of the temperature module by pressing the tab and sliding the cover to the right.

Aggiungi Commento

Depress the spring tab on the temperature probe cable connector and withdraw it from the probe port. Depress the spring tab on the temperature probe cable connector and withdraw it from the probe port. Depress the spring tab on the temperature probe cable connector and withdraw it from the probe port.
  • Depress the spring tab on the temperature probe cable connector and withdraw it from the probe port.

Aggiungi Commento

Remove the flathead screw on the USB networking door.
  • Remove the flathead screw on the USB networking door.

  • Loosen the captive Phillips #2 screw securing the monitor to the stand.

Aggiungi Commento

Holding the monitor securely, open the USB networking door.
  • Holding the monitor securely, open the USB networking door.

    • You may have to lift the monitor slightly to allow the door to swing out from the stand mount.

Aggiungi Commento

Detach any accessory USB cables from USB ports on the monitor. Detach any accessory USB cables from USB ports on the monitor.
  • Detach any accessory USB cables from USB ports on the monitor.

Aggiungi Commento

Slide the monitor off of the stand tray. Slide the monitor off of the stand tray. Slide the monitor off of the stand tray.
  • Slide the monitor off of the stand tray.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Sam Lionheart

Membro da: 18/10/2012

322.176 Reputazione

1.663 Guide realizzate

Team

iFixit Membro di iFixit

Community

113 Membri

5.982 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 2

Tutti i Tempi: 325