Introduzione

This guide walks you through the steps to replace the external speaker on your phone. You can follow these same steps to check your speaker connection as well.

To power off the phone, press the on/off button on top.
  • To power off the phone, press the on/off button on top.

Aggiungi Commento

Slide the battery cover down to remove.
  • Slide the battery cover down to remove.

Aggiungi Commento

Pull the battery removal tab and lift out the battery. If the battery removal tab is missing, place a spudger on the opposite side of the highlighted connector and pry the battery up. If the battery removal tab is missing, place a spudger on the opposite side of the highlighted connector and pry the battery up.
  • Pull the battery removal tab and lift out the battery.

  • If the battery removal tab is missing, place a spudger on the opposite side of the highlighted connector and pry the battery up.

Aggiungi Commento

Remove the two 4.0-mm #000 Phillips screws at the top of the battery compartment.  Tweezers may be useful to remove the screws.
  • Remove the two 4.0-mm #000 Phillips screws at the top of the battery compartment. Tweezers may be useful to remove the screws.

Aggiungi Commento

Use firm pressure to carefully pry off the cover with your fingers. Use firm pressure to carefully pry off the cover with your fingers.
  • Use firm pressure to carefully pry off the cover with your fingers.

Aggiungi Commento

Remove the 4.0-mm #00 Phillips screw securing the camera flash circuit board.  The board is still connected by a connector on the bottom of the board.
  • Remove the 4.0-mm #00 Phillips screw securing the camera flash circuit board. The board is still connected by a connector on the bottom of the board.

Aggiungi Commento

Gently pry off the camera flash circuit board with the spudger.
  • Gently pry off the camera flash circuit board with the spudger.

Aggiungi Commento

Gently pry off the camera with the spudger.
  • Gently pry off the camera with the spudger.

Aggiungi Commento

Remove the four 5.0-mm Torx T6 screws from the corners of the black cover.
  • Remove the four 5.0-mm Torx T6 screws from the corners of the black cover.

Aggiungi Commento

Remove the 4.0-mm #00 Phillips screw that holds the wireless antenna in place.  The antenna does not need to be removed.
  • Remove the 4.0-mm #00 Phillips screw that holds the wireless antenna in place. The antenna does not need to be removed.

Aggiungi Commento

Use the spudger and plastic opening tools to apply firm but gentle pressure equally around the outside of the case. Carefully pry the black portion of the case away from the silver portion. Do not try to remove case completely.  The speaker wire is still connected to the motherboard.
  • Use the spudger and plastic opening tools to apply firm but gentle pressure equally around the outside of the case.

  • Carefully pry the black portion of the case away from the silver portion.

  • Do not try to remove case completely. The speaker wire is still connected to the motherboard.

Aggiungi Commento

Using tweezers, pull on the connector or wire in the direction of the wire with gentle pressure to unplug the wire connector from the motherboard.
  • Using tweezers, pull on the connector or wire in the direction of the wire with gentle pressure to unplug the wire connector from the motherboard.

Aggiungi Commento

Press your finger on the speaker from the outside of the housing, and the speaker will come out. Press your finger on the speaker from the outside of the housing, and the speaker will come out.
  • Press your finger on the speaker from the outside of the housing, and the speaker will come out.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 87