Introduzione

The motherboard is a essential part that contains the CPU and runs your computer and its systems, if its damaged then most likely it'll have to be replaced. This guide will show you how to get to the motherboard and replace it.

Parti

Nessuna parte richiesta.

Make sure your computer is turned off and the computer is not plugged in. Turn your laptop upside down, and slide the right release tab outward.
  • Make sure your computer is turned off and the computer is not plugged in.

  • Turn your laptop upside down, and slide the right release tab outward.

  • Using you left hand, hold the left release tab towards the left side and then pull the battery out.

Aggiungi Commento

Flip the laptop over so it is rightside up, and open the laptop all the way so that the screen is horizontal.
  • Flip the laptop over so it is rightside up, and open the laptop all the way so that the screen is horizontal.

Aggiungi Commento

Using the plastic opening tool, pry off the panel above the keyboard, starting near the right front speaker. Use the plastic opening tool to pop off tabs along the length of this panel. This may feel like you're about to break something, but as long as you work your way down the panel and don't yank it out, the laptop will be fine.
  • Using the plastic opening tool, pry off the panel above the keyboard, starting near the right front speaker.

  • Use the plastic opening tool to pop off tabs along the length of this panel.

  • This may feel like you're about to break something, but as long as you work your way down the panel and don't yank it out, the laptop will be fine.

Aggiungi Commento

Unscrew the two 4.5 mm screws holding the keyboard on with the Phillips #1 screwdriver. Unscrew the two 4.5 mm screws holding the keyboard on with the Phillips #1 screwdriver.
  • Unscrew the two 4.5 mm screws holding the keyboard on with the Phillips #1 screwdriver.

Aggiungi Commento

Lift the keyboard gently from the side closest the screen. Pull out the ribbon connecting the keyboard to the laptop. Pull out the ribbon connecting the keyboard to the laptop.
  • Lift the keyboard gently from the side closest the screen.

  • Pull out the ribbon connecting the keyboard to the laptop.

Aggiungi Commento

Disconnect wire attaching LCD to motherboard Using the Phillips screwdriver remove the two 4.0mm screws from each hinge above speakers Partially close the lid and remove the last two 4.0mm screws from the back of the laptop.
  • Disconnect wire attaching LCD to motherboard

  • Using the Phillips screwdriver remove the two 4.0mm screws from each hinge above speakers

  • Partially close the lid and remove the last two 4.0mm screws from the back of the laptop.

Aggiungi Commento

Remove the seventeen 4.5mm phillips screws on the bottom of the laptop. Using the pry tool separate the two halves of the laptop base.
  • Remove the seventeen 4.5mm phillips screws on the bottom of the laptop.

  • Using the pry tool separate the two halves of the laptop base.

  • Use caution when separating the laptop halves as they are still connected by two ribbon cables.

Aggiungi Commento

Lift the top half of the case enough to get your hand beneath it, and then remove the two ribbon cables that connect it to the motherboard. Lift the top half of the case enough to get your hand beneath it, and then remove the two ribbon cables that connect it to the motherboard.
  • Lift the top half of the case enough to get your hand beneath it, and then remove the two ribbon cables that connect it to the motherboard.

Aggiungi Commento

Remove the upper half of laptop and place bottom half in the center of your workspace. Remove the one 2.00mm phillips screw. Remove the ribbon cable connecting the USB ports to the motherboard.
  • Remove the upper half of laptop and place bottom half in the center of your workspace.

  • Remove the one 2.00mm phillips screw.

  • Remove the ribbon cable connecting the USB ports to the motherboard.

Aggiungi Commento

Remove the two 2.5mm phillips screws holding the spring retainer for the heat sink. Remove the two 4.0mm phillips screws holding the fan in place. Remove the fan power connector.
  • Remove the two 2.5mm phillips screws holding the spring retainer for the heat sink.

  • Remove the two 4.0mm phillips screws holding the fan in place.

  • Remove the fan power connector.

Aggiungi Commento

Lift fan and heat sink out of case.
  • Lift fan and heat sink out of case.

Aggiungi Commento

Lift the power jack straight up and out of the slots that hold it in.
  • Lift the power jack straight up and out of the slots that hold it in.

Aggiungi Commento

Lift the motherboard out of the bottom case. Lift the motherboard out of the bottom case.
  • Lift the motherboard out of the bottom case.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 3

Ultimi 7 Giorni: 15

Ultimi 30 Giorni: 60

Tutti i Tempi: 1,510