Flip the phone over so that the screen is facing down.
  • Flip the phone over so that the screen is facing down.

Aggiungi Commento

Push the gray lever up towards the top of the phone. Pull up on the battery pack and completely separate it from the phone.
  • Push the gray lever up towards the top of the phone.

  • Pull up on the battery pack and completely separate it from the phone.

Aggiungi Commento

Locate the 5 screws around the back casing. Use a three-prong screw bit to remove all 5 screws
  • Locate the 5 screws around the back casing.

  • Use a three-prong screw bit to remove all 5 screws

Aggiungi Commento

Use the plastic opening tool and slide it around the phone to pull apart the front and back casing.
  • Use the plastic opening tool and slide it around the phone to pull apart the front and back casing.

Aggiungi Commento

Separate the two cases.
  • Separate the two cases.

Aggiungi Commento

Use the plastic opening tool to remove the motherboard from the front case.
  • Use the plastic opening tool to remove the motherboard from the front case.

Aggiungi Commento

Locate the 4 white clips of the dispaly. Locate the 4 white clips of the dispaly.
  • Locate the 4 white clips of the dispaly.

Aggiungi Commento

Using the plastic opening tool, pull the white clips of the display away from the printed circuit board to unclip display. Using the plastic opening tool, pull the white clips of the display away from the printed circuit board to unclip display.
  • Using the plastic opening tool, pull the white clips of the display away from the printed circuit board to unclip display.

Aggiungi Commento

Grasp the display on both sides and carefully pull the display off of the printed circuit board. Grasp the display on both sides and carefully pull the display off of the printed circuit board.
  • Grasp the display on both sides and carefully pull the display off of the printed circuit board.

Aggiungi Commento

Using the plastic opening tool, carefully remove the yellow film covering the display connector. Do not damage the yellow film. Ensure that it stays in one piece and does not tear.
  • Using the plastic opening tool, carefully remove the yellow film covering the display connector.

    • Do not damage the yellow film. Ensure that it stays in one piece and does not tear.

Aggiungi Commento

Use a Phillips-head screw bit to remove the screw under the yellow film
  • Use a Phillips-head screw bit to remove the screw under the yellow film

Aggiungi Commento

Use the spudger tool to pry the latches ways from the circuit board Detach the metal casing from the circuit board Detach the metal casing from the circuit board
  • Use the spudger tool to pry the latches ways from the circuit board

  • Detach the metal casing from the circuit board

Aggiungi Commento

Remove wires attaching vibrator motor to circuit board gently so as not to damage them Remove wires attaching vibrator motor to circuit board gently so as not to damage them
  • Remove wires attaching vibrator motor to circuit board gently so as not to damage them

Aggiungi Commento

Once the metal casing is removed from the circuit board take it and locate the vibrator motor on the top side of the casing Use the spudger tool to gently pry the vibrator motor out of its protective shell Use the spudger tool to gently pry the vibrator motor out of its protective shell
  • Once the metal casing is removed from the circuit board take it and locate the vibrator motor on the top side of the casing

  • Use the spudger tool to gently pry the vibrator motor out of its protective shell

Aggiungi Commento

With the vibrator motor completely removed, you can now replace it with a new one
  • With the vibrator motor completely removed, you can now replace it with a new one

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Austin Shores

Membro da: 18/10/2013

301 Reputazione

6 Guide realizzate

Team

Clemson, Team 13-5, Benson Fall 2013 Membro di Clemson, Team 13-5, Benson Fall 2013

CLEM-BENSON-F13S13G5

3 Membri

12 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 3

Tutti i Tempi: 193