Introduzione

This guide give instructions on how to locate the speaker for removal and/or repair.

Parti

Nessuna parte richiesta.

Flip over the phone and then slide down the back cover with your thumb.
  • Flip over the phone and then slide down the back cover with your thumb.

Aggiungi Commento

Lever out the battery from the phone using your thumb.
  • Lever out the battery from the phone using your thumb.

Aggiungi Commento

With the phone closed, run a plastic opening tool along the seam of the top half of the phone Make sure to disconnect each of the five clips before proceeding (2 on each side, 1 on top) Make sure to disconnect each of the five clips before proceeding (2 on each side, 1 on top)
  • With the phone closed, run a plastic opening tool along the seam of the top half of the phone

  • Make sure to disconnect each of the five clips before proceeding (2 on each side, 1 on top)

Aggiungi Commento

Using T6 Torx Screwdriver, remove the four 3.16mm screws from the front panel Note that the fourth screw is under a fold in the ribbon cable
  • Using T6 Torx Screwdriver, remove the four 3.16mm screws from the front panel

  • Note that the fourth screw is under a fold in the ribbon cable

Aggiungi Commento

Starting in the lower right corner, slowly start to lift the tape that is holding the front LCD and cables down Be careful around the two ribbon cables that are attached to the tape, they are fragile Lift the tape from the board
  • Starting in the lower right corner, slowly start to lift the tape that is holding the front LCD and cables down

  • Be careful around the two ribbon cables that are attached to the tape, they are fragile

  • Lift the tape from the board

Aggiungi Commento

Using a plastic opening tool, lift the ribbon cable connection below the front LCD
  • Using a plastic opening tool, lift the ribbon cable connection below the front LCD

Aggiungi Commento

Using a plastic opening tool, slowly pry up the LCD display from the bottom, releasing it from the glue holding it to the board Using a plastic opening tool, slowly pry up the LCD display from the bottom, releasing it from the glue holding it to the board Using a plastic opening tool, slowly pry up the LCD display from the bottom, releasing it from the glue holding it to the board
  • Using a plastic opening tool, slowly pry up the LCD display from the bottom, releasing it from the glue holding it to the board

Aggiungi Commento

Locate the ribbon cable connection in the upper right hand corner of the board
  • Locate the ribbon cable connection in the upper right hand corner of the board

  • Using a plastic opening tool, lift off the cable from the board

  • Be gentle and make sure not to rip the ribbon cable

Aggiungi Commento

Using a plastic opening tool, slowly work the board off the mounts holding it to the frame Flip the board over to reveal the main display
  • Using a plastic opening tool, slowly work the board off the mounts holding it to the frame

  • Flip the board over to reveal the main display

Aggiungi Commento

Locate the ribbon cable for the main display on the bottom of the board
  • Locate the ribbon cable for the main display on the bottom of the board

  • Slowly lift off the ribbon connector from its housing using a plastic opening tool

Aggiungi Commento

Slowly wedge the plastic opening tool under the bottom of the main display Separate the display from the glue lifting it off the board
  • Slowly wedge the plastic opening tool under the bottom of the main display

  • Separate the display from the glue lifting it off the board

Aggiungi Commento

Using a case opening tool, gently pry the speaker in the bottom corner from the glue from right to left until it pops out.
  • Using a case opening tool, gently pry the speaker in the bottom corner from the glue from right to left until it pops out.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Andrew

Membro da: 04/10/2010

358 Reputazione

8 Guide realizzate

Team

Cal Poly, Team 4-46, Amido Fall 2010 Membro di Cal Poly, Team 4-46, Amido Fall 2010

CPSU-AMIDO-F10S4G46

4 Membri

14 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 4

Tutti i Tempi: 410