Salta al contenuto principale

Sony Vaio VGN-SZ120P screen Replacement

Cosa ti serve

  1. Sony Vaio VGN-SZ120P screen Replacement, Battery: passo 1, immagine 1 di 1
    • Set the computer display-side down.

    • Unlock the battery by sliding the port-side latch to the 'unlock' position.

  2. Sony Vaio VGN-SZ120P screen Replacement: passo 2, immagine 1 di 1
    • On the opposite side of the battery, press the release latch and slide the battery away from the main body to remove.

  3. Sony Vaio VGN-SZ120P screen Replacement, Keyboard: passo 3, immagine 1 di 1
    • Ignore the removal of the heat sink and memory panels as depicted. They do not need to be removed for the completion of this guide.

    • Remove the Torx security screw near the center of the battery-side edge.

  4. Sony Vaio VGN-SZ120P screen Replacement: passo 4, immagine 1 di 2 Sony Vaio VGN-SZ120P screen Replacement: passo 4, immagine 2 di 2
    • Press the tabs on each side of the display-side of the keyboard with the flat edge of a spudger.

    • Pull the keyboard toward the mouse pad and gently lift up.

  5. Sony Vaio VGN-SZ120P screen Replacement: passo 5, immagine 1 di 2 Sony Vaio VGN-SZ120P screen Replacement: passo 5, immagine 2 di 2
    • The keyboard is still attached by ribbon cable, don't try to remove the keyboard entirely yet.

    • Disconnect the ribbon cable by pressing the tabs on either side of the connector. Pull the cable out parallel to the connector.

    • Remove the keyboard.

  6. Sony Vaio VGN-SZ120P screen Replacement, Mouse Assembly: passo 6, immagine 1 di 1
    • Turn the laptop upside down.

    • Remove the three screws from the front mouse panel located on the bottom of the laptop.

    • Carefully flip the laptop back over. Remove three more screws from the top securing the panel. A ribbon cable will still be attached to the panel when you remove it.

  7. Sony Vaio VGN-SZ120P screen Replacement: passo 7, immagine 1 di 2 Sony Vaio VGN-SZ120P screen Replacement: passo 7, immagine 2 di 2
    • Lift the mouse assembly just enough to access the connecting ribbon cable.

    • Lift the ribbon cable lock to remove the cable.

    • Carefully remove the mouse panel assembly and set aside.

  8. Sony Vaio VGN-SZ120P screen Replacement, Speaker Assembly: passo 8, immagine 1 di 3 Sony Vaio VGN-SZ120P screen Replacement, Speaker Assembly: passo 8, immagine 2 di 3 Sony Vaio VGN-SZ120P screen Replacement, Speaker Assembly: passo 8, immagine 3 di 3
    • Remove the four screws from the underside of the computer. These screws are located underneath where the battery sits and secure the top keyboard panel.

    • To remove the panel below the screen, press up on the two tabs holding the panel in and lift up. The panel should pop off.

    • Before proceeding, remove all black tape holding down wires and other cabling.

  9. Sony Vaio VGN-SZ120P screen Replacement: passo 9, immagine 1 di 1
    • Pop off the antenna using a pair of tweezers.

  10. Sony Vaio VGN-SZ120P screen Replacement: passo 10, immagine 1 di 1
    • Remove the seven philips screws holding the speaker assembly in place.

    • Before removing the assembly, disconnect the ribbon cable located at the top left corner of the assembly.

    • The speaker assembly will come off with the display assembly.

  11. Sony Vaio VGN-SZ120P screen Replacement, screen: passo 11, immagine 1 di 2 Sony Vaio VGN-SZ120P screen Replacement, screen: passo 11, immagine 2 di 2
    • Caution: Be careful of snags when pulling up assembly and speakers.

    • To remove the VGA cable, lift up on the metal bracket and gently lift the connector off the logic board.

    • To remove the webcam cable, lift up the connector from the logic board gently.

  12. Sony Vaio VGN-SZ120P screen Replacement: passo 12, immagine 1 di 3 Sony Vaio VGN-SZ120P screen Replacement: passo 12, immagine 2 di 3 Sony Vaio VGN-SZ120P screen Replacement: passo 12, immagine 3 di 3
    • Unscrew the four securing screws, two on each side of the LCD.

    • Carefully remove the LCD. The speaker, bluetooth, and webcam assembly will come up with the display assembly.

    • Caution: Be careful of snags when pulling up display and speaker assemblies.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Colin Glaves

Membro da: 04/09/10

458 Reputazione

2 Guide realizzate

Team

Cal Poly, Team 25-89, Amido Spring 2010 Membro di Cal Poly, Team 25-89, Amido Spring 2010

CPSU-AMIDO-S10S25G89

4 Membri

63 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 4

Tutti i Tempi: 7,725