Parti

Nessuna parte richiesta.

Slide the battery latch down the side of the camera with your hands.
  • Slide the battery latch down the side of the camera with your hands.

  • The latch will automatically pop open.

Aggiungi Commento

Unlatch the clip over the battery.
  • Unlatch the clip over the battery.

  • The battery will partially pop out.

Aggiungi Commento

Remove the battery from the camera. Remove the battery from the camera.
  • Remove the battery from the camera.

Aggiungi Commento

Remove the four 3.0mm Phillips #000 screws on the top of the camera with the phillips screwdriver. Remove the additional four 3.0mm Phillips #000 screws on the bottom of the camera.
  • Remove the four 3.0mm Phillips #000 screws on the top of the camera with the phillips screwdriver.

  • Remove the additional four 3.0mm Phillips #000 screws on the bottom of the camera.

Aggiungi Commento

Once the screws are removed, slowly remove the back casing from the rest of the camera. Once the screws are removed, slowly remove the back casing from the rest of the camera.
  • Once the screws are removed, slowly remove the back casing from the rest of the camera.

Aggiungi Commento

Then, pull the front case away from the rest of the camera. Then, pull the front case away from the rest of the camera.
  • Then, pull the front case away from the rest of the camera.

Aggiungi Commento

After the casing is removed, the camera should look as shown.
  • After the casing is removed, the camera should look as shown.

Aggiungi Commento

Dislodge the round casing from the lens. Pull it away from the rest of the camera.
  • Dislodge the round casing from the lens.

  • Pull it away from the rest of the camera.

Aggiungi Commento

Unscrew the two 4.0mm Phillips #000 screws from the display.
  • Unscrew the two 4.0mm Phillips #000 screws from the display.

Aggiungi Commento

Pull the two ribbon cables out of their slots on the back circuit board.
  • Pull the two ribbon cables out of their slots on the back circuit board.

Aggiungi Commento

Remove the three 4.0mm Phillips #000 screws holding the back panel in place.
  • Remove the three 4.0mm Phillips #000 screws holding the back panel in place.

Aggiungi Commento

Work the back panel out from under the small grey clip. Slide the back panel off of the camera by dislodging it from the remaining clips. Below is a flat, orange cable connecting the lens to the motherboard.
  • Work the back panel out from under the small grey clip.

  • Slide the back panel off of the camera by dislodging it from the remaining clips.

  • Below is a flat, orange cable connecting the lens to the motherboard.

  • Be careful not to bend the back plate during this process.

Aggiungi Commento

Turn the camera over so that you can see the front of the lens.
  • Turn the camera over so that you can see the front of the lens.

  • Two connectors link the lens to the motherboard.

  • Gently bring the lens away from the camera.

Aggiungi Commento

Using the flat end of the plastic spudger tool, flip up the black tabs on the connectors.
  • Using the flat end of the plastic spudger tool, flip up the black tabs on the connectors.

  • Be careful not to exert too much force, as the connectors are delicate.

Aggiungi Commento

Gently pull out the cables and move the lens away from the rest of the camera. You should now have two distinct, separate components. You should now have two distinct, separate components.
  • Gently pull out the cables and move the lens away from the rest of the camera.

  • You should now have two distinct, separate components.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Sean Sayles

Membro da: 09/05/2012

7 Reputazione

1 Guida realizzata

Team

Cal Poly, Team 17-25, Amido Spring 2012 Membro di Cal Poly, Team 17-25, Amido Spring 2012

CPSU-AMIDO-S12S17G25

4 Membri

7 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 7

Tutti i Tempi: 1,038