Introduzione

This guide will show how to replace a motherboard. The motherboard could be causing faulty display, not turning on, and bad sound quality on a continuous basis.

Before any repair work can be done, one must remove the device from the vehicle. To do so follow this link to see a vehicle general removal of a stereo system.

Parti

Nessuna parte richiesta.

Locate face-plate eject button.
  • Locate face-plate eject button.

Aggiungi Commento

Press the eject button. Remove the face-plate.
  • Press the eject button.

  • Remove the face-plate.

Aggiungi Commento

Remove two 4.9mm Phillips #00screws on the front of the device. Remove two 7.5mm Phillips #00screws on the front of the device. When the screws are removed, the eject lever may fall into the device. Make sure the device is held horizontal and level.
  • Remove two 4.9mm Phillips #00screws on the front of the device.

  • Remove two 7.5mm Phillips #00screws on the front of the device.

  • When the screws are removed, the eject lever may fall into the device. Make sure the device is held horizontal and level.

The screws in red do not seem to need to be removed unless you are trying to replace the eject lever. If you're not trying to replace the lever, it adds an unnecessary complication to putting it back together.

Dale Pearson - Replica

Rotate device 90 degrees to either side. Use the plastic opening tool to pry open the top and bottom tab respectively.
  • Rotate device 90 degrees to either side.

  • Use the plastic opening tool to pry open the top and bottom tab respectively.

  • Repeat on opposite side.

Aggiungi Commento

Remove front panel.
  • Remove front panel.

Aggiungi Commento

Locate the clip on the wiring harness.
  • Locate the clip on the wiring harness.

Aggiungi Commento

Press down on the clip like you would an Ethernet cable. Rock harness side to side, pulling gently towards you until harness detaches.
  • Press down on the clip like you would an Ethernet cable.

  • Rock harness side to side, pulling gently towards you until harness detaches.

Aggiungi Commento

Locate back panel.
  • Locate back panel.

Aggiungi Commento

Remove four 11.5mm Phillips #00 (silver) screws from back panel. Remove four 11.5mm Phillips #00 (silver) screws from back panel. Remove four 11.5mm Phillips #00 (silver) screws from back panel.
  • Remove four 11.5mm Phillips #00 (silver) screws from back panel.

Aggiungi Commento

Remove four 9.5mm Phillips #00 (black) screws from back panel.
  • Remove four 9.5mm Phillips #00 (black) screws from back panel.

  • Remove two 7.5mm Phillips #00 (black) screws from back panel.

Aggiungi Commento

Remove back panel.
  • Remove back panel.

  • On the back panel there will be thermal (white) paste. Do not touch.

Aggiungi Commento

Remove one  9.5mm Phillips #00 screw.
  • Remove one 9.5mm Phillips #00 screw.

  • Rotate device 180 degrees and repeat step.

Aggiungi Commento

Using plastic opening tool, detach the tabs. There are two on either side. You will need to apply a decent amount of force to detach.
  • Using plastic opening tool, detach the tabs. There are two on either side.

  • You will need to apply a decent amount of force to detach.

Aggiungi Commento

Remove top panel. Remove top panel.
  • Remove top panel.

Aggiungi Commento

Pull up CD drive slightly.
  • Pull up CD drive slightly.

Aggiungi Commento

Disconnect motherboard connection.
  • Disconnect motherboard connection.

Aggiungi Commento

Remove CD drive.
  • Remove CD drive.

Aggiungi Commento

Remove three 6.7mm Phillips 300 screws.
  • Remove three 6.7mm Phillips 300 screws.

Aggiungi Commento

Pull motherboard up.
  • Pull motherboard up.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Team

USF Tampa, Team 10-2, Brown Fall 2014 Membro di USF Tampa, Team 10-2, Brown Fall 2014

USFT-BROWN-F14S10G2

3 Membri

7 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 6

Ultimi 30 Giorni: 29

Tutti i Tempi: 810