Introduzione

In this guide, we will take the Skullcandy Air Raid apart so that the USB motherboard can be replaced.

Starting with the corners, gently pull the rubber cover off of the device.
  • Starting with the corners, gently pull the rubber cover off of the device.

Aggiungi Commento

Using the T-6 hexagonal screwdriver, unscrew the four 10mm #6 hex screws on the right side of the device.
  • Using the T-6 hexagonal screwdriver, unscrew the four 10mm #6 hex screws on the right side of the device.

  • Remove the handle from the device.

Aggiungi Commento

Unscrew the two screws on the left side of the device using the phillips #00 screwdriver.
  • Unscrew the two screws on the left side of the device using the phillips #00 screwdriver.

    • One 5mm Phillips screw.

    • One 8mm Phillips screw.

Aggiungi Commento

Gently pull the sides of the front plate outwards from the device.
  • Gently pull the sides of the front plate outwards from the device.

  • Pull up on the front plate to remove it from the device.

Aggiungi Commento

Using a #000 Philips Screwdriver, unscrew the four 8 mm Philips screws from each corner of both speakers (eight 8 mm Philips screws total).
  • Using a #000 Philips Screwdriver, unscrew the four 8 mm Philips screws from each corner of both speakers (eight 8 mm Philips screws total).

Aggiungi Commento

Using the plastic opening tool, pry around edges of the speaker to loosen glue contact with front plate.
  • Using the plastic opening tool, pry around edges of the speaker to loosen glue contact with front plate.

  • If you are unable to loosen glue contact using the plastic opening tool, use a heat gun to assist in removal.

Aggiungi Commento

Lift the speaker out of the device.
  • Lift the speaker out of the device.

  • Be aware of the connection with the ribbon cable.

  • For reassembly, ensure proper orientation of the cable plug.

Aggiungi Commento

Firmly pull on the end of ribbon cable to disconnect the speaker from the motherboard.
  • Firmly pull on the end of ribbon cable to disconnect the speaker from the motherboard.

Aggiungi Commento

Using a Phillips #00 Precision Screwdriver, unscrew two 6 mm screws from the middle of the panel, above and below volume buttons.
  • Using a Phillips #00 Precision Screwdriver, unscrew two 6 mm screws from the middle of the panel, above and below volume buttons.

Aggiungi Commento

Lift the button panel.
  • Lift the button panel.

Aggiungi Commento

Using a Phillips #00 Precision Screwdriver, unscrew two 6 mm screws from the button motherboard.
  • Using a Phillips #00 Precision Screwdriver, unscrew two 6 mm screws from the button motherboard.

Aggiungi Commento

Using a plastic opening tool, pry the button motherboard to detach it from the device.
  • Using a plastic opening tool, pry the button motherboard to detach it from the device.

  • The button motherboard is connected to a ribbon cable inside the device.

Aggiungi Commento

Pull the black ribbon cord attachment away from the motherboard.
  • Pull the black ribbon cord attachment away from the motherboard.

  • Pull on the cable until it releases from the back of the motherboard.

    • The black attachment is part of the connector, not the blue ribbon cable, so it will not disconnect from the motherboard.

Aggiungi Commento

Using a Phillips #00 Precision Screwdriver, unscrew two 8 mm screws. Lift off the back panel.
  • Using a Phillips #00 Precision Screwdriver, unscrew two 8 mm screws.

  • Lift off the back panel.

How do you pull off the back panel? Those two parts are really stuck to each other.

Brandon De La Rosa - Replica

Where the blue and white ribbon cable meets the motherboard, pull up on the black piece of the ribbon cable connector.
  • Where the blue and white ribbon cable meets the motherboard, pull up on the black piece of the ribbon cable connector.

  • Pull the ribbon cable away from the motherboard.

Aggiungi Commento

Pull on grey and white ribbon cable until it disconnects from the motherboard.
  • Pull on grey and white ribbon cable until it disconnects from the motherboard.

Aggiungi Commento

Using a Phillips #00 Precision Screwdriver, unscrew two 6 mm screws from the left divider between the main cavity and the USB motherboard. Pull out the USB/On Switch panel. Pull out the Left Divider.
  • Using a Phillips #00 Precision Screwdriver, unscrew two 6 mm screws from the left divider between the main cavity and the USB motherboard.

  • Pull out the USB/On Switch panel.

  • Pull out the Left Divider.

    • For reassembly, lift up on right side of motherboard to slide left divider back in place.

Aggiungi Commento

Using a Phillips #00 Precision Screwdriver, unscrew two 5 mm Phillips-head screws from the USB motherboard. Remove the metal clip.
  • Using a Phillips #00 Precision Screwdriver, unscrew two 5 mm Phillips-head screws from the USB motherboard.

  • Remove the metal clip.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Cyrene

Membro da: 13/01/2015

158 Reputazione

1 Guida realizzata

Where can you purchase the replacement?

Mikail Lane - Replica

As far as I know,You can't!

Luke Thomas - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 16

Tutti i Tempi: 723