Salta al contenuto principale

Sharper Image iPulse SI325 Motherboard Replacement

Cosa ti serve

  1. Sharper Image iPulse SI325 Motherboard Replacement, Outer Case: passo 1, immagine 1 di 2 Sharper Image iPulse SI325 Motherboard Replacement, Outer Case: passo 1, immagine 2 di 2
    • Gently position the device so that the buttons and speakers lie face down.

    • Unplug the power cord from the "DC Input."

  2. Sharper Image iPulse SI325 Motherboard Replacement: passo 2, immagine 1 di 3 Sharper Image iPulse SI325 Motherboard Replacement: passo 2, immagine 2 di 3 Sharper Image iPulse SI325 Motherboard Replacement: passo 2, immagine 3 di 3
    • Remove the four 12mm phillips head #2 screws located along the outer edge of the white case.

    • Be careful! There are two small, easily-broken, plastic tabs at the bottom of the device keeping it together.

    • Once you remove the screws, pick the device up so that the grey label on the bottom of the device faces toward you.

    • With your thumbs on either side of the grey label, slowly push with both thumbs until the case pops open.

    • A small gap will open as the two tabs are released.

    • Do not pull the two halves apart yet. They are held together by the speaker wire.

  3. Sharper Image iPulse SI325 Motherboard Replacement: passo 3, immagine 1 di 2 Sharper Image iPulse SI325 Motherboard Replacement: passo 3, immagine 2 di 2
    • Grip both sides of the top round part of the case and carefully open it like a clam. The bottom of the two halves are connected by the speaker wire. Do not separate by more than 1 centimeter.

    • Grip either side of the top round part of the case and carefully open the device to reveal all the hidden treasures inside!

    • Lay the device down, so that all the internal components are facing upwards.

  4. Sharper Image iPulse SI325 Motherboard Replacement, Motherboard: passo 4, immagine 1 di 1
    • Turn the device over so that the internals are facing down.

    • Remove the three 7mm Phillips #1 screws connecting the Zipconnect unit.

  5. Sharper Image iPulse SI325 Motherboard Replacement: passo 5, immagine 1 di 2 Sharper Image iPulse SI325 Motherboard Replacement: passo 5, immagine 2 di 2
    • Turn the device over again so you are looking at the internals.

    • The Zipconnect unit will lift out but will still be attached by a wire connected to the motherboard.

    • Remove the six 7mm Phillips #1 phillips screws attatching the Zipconnect unit to the motherboard wire and set the unit out of the way.

  6. Sharper Image iPulse SI325 Motherboard Replacement: passo 6, immagine 1 di 2 Sharper Image iPulse SI325 Motherboard Replacement: passo 6, immagine 2 di 2
    • Disconnect the speaker wire from the motherboard by firmly griping the wires close to the connection with two fingers and pull the connector out.

    • Wiggling the connector back and forth as you pull will make removal easier.

  7. Sharper Image iPulse SI325 Motherboard Replacement: passo 7, immagine 1 di 1
    • Remove the two 11mm Phillips #1 screws attaching the small brown circuit board to the plastic outer case.

    • Also remove the four 11mm Phillips #1 screws attaching the motherboard to the plastic case.

  8. Sharper Image iPulse SI325 Motherboard Replacement: passo 8, immagine 1 di 3 Sharper Image iPulse SI325 Motherboard Replacement: passo 8, immagine 2 di 3 Sharper Image iPulse SI325 Motherboard Replacement: passo 8, immagine 3 di 3
    • Lift up on both the motherboard and brown circuit board which contains the light intensity dial.

    • Turn over the motherboard and remove the solder connecting the wide, flat, grey wire.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Vi Le

Membro da: 10/14/13

101 Reputazione

1 Guida realizzata

Team

Cal Poly, Team 11-33, Amido Fall 2013 Membro di Cal Poly, Team 11-33, Amido Fall 2013

CPSU-AMIDO-F13S11G33

4 Membri

8 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 1

Tutti i Tempi: 536