Introduzione

A guide to installing a replacement screen on a Sega Game Gear.

Parti

Nessuna parte richiesta.

Place your device upside down and locate the two battery compartments.
  • Place your device upside down and locate the two battery compartments.

Aggiungi Commento

Press on the tabs at the bottom of the battery covers then lift up to remove.
  • Press on the tabs at the bottom of the battery covers then lift up to remove.

  • Remove batteries if they are present.

Aggiungi Commento

Remove the following screws:
  • Remove the following screws:

    • Seven Phillips scres

    • One 4.5 mm Gamebit screw

Aggiungi Commento

Use tweezers to take all other screws out.
  • Use tweezers to take all other screws out.

Aggiungi Commento

Gently open the case by unfolding it over the top of the Sega Game Gear. Do not pull the back of the case away, as cables are connected between both sides.
  • Gently open the case by unfolding it over the top of the Sega Game Gear.

  • Do not pull the back of the case away, as cables are connected between both sides.

Aggiungi Commento

Carefully unplug the 2 white-tipped connectors on the top cover. Carefully unplug the 2 white-tipped connectors on the top cover. Carefully unplug the 2 white-tipped connectors on the top cover.
  • Carefully unplug the 2 white-tipped connectors on the top cover.

Aggiungi Commento

Unscrew all the marked screws.
  • Unscrew all the marked screws.

Aggiungi Commento

Slide the logic board out from under the circular black fastener at the top-left corner of the case.
  • Slide the logic board out from under the circular black fastener at the top-left corner of the case.

Aggiungi Commento

Place the board onto a flat surface.
  • Place the board onto a flat surface.

  • Small plastic buttons may fall off during this process, save them in a container or a place where they could be found later on.

Aggiungi Commento

Unscrew the marked screws.
  • Unscrew the marked screws.

  • Flip the board, having its back facing up.

  • Hold onto the screen in the back, as it will flip open if not held onto.

Aggiungi Commento

Make sure the screen is towards the bottom, as indicated in the second picture. Make sure the screen is towards the bottom, as indicated in the second picture.
  • Make sure the screen is towards the bottom, as indicated in the second picture.

Aggiungi Commento

Gently open the screen up. The screen will not come out all the way since it is glued onto the top side.
  • Gently open the screen up.

  • The screen will not come out all the way since it is glued onto the top side.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 8 persone hanno completato questa guida.

Team

Cal Poly, Team 28-33, Regan Spring 2010 Membro di Cal Poly, Team 28-33, Regan Spring 2010

CPSU-REGAN-S10S28G33

5 Membri

6 Guide realizzate

any one know where to get a new display that wont bleed me dry?

isaiah bellamy (masta ike) - Replica

Due to the nature a Game Gear screen attaches, a ribbon directly soldered to the mainboard, replacing it requires a soldering iron and some fairly advanced technique.

This guide, titled “Sega Game Gear Screen Replacement”, only takes us to the point you remove the ribbon. There is much work left.

Anthony Bessel - Replica

so, uh, is there a more comprehensive version somewhere?

rollin -

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 15

Ultimi 7 Giorni: 70

Ultimi 30 Giorni: 341

Tutti i Tempi: 39,649