Introduzione

This guide will provide a step-by-step procedure for replacing the OLED screen in your Samsung Rogue. This is one of the more difficult repair guides because it requires a lot of disassembling.

Before disassembling your Samsung Rogue, make sure it is powered off. With your thumbs, push down on the back cover of your phone and slide it away from the camera.
  • Before disassembling your Samsung Rogue, make sure it is powered off.

  • With your thumbs, push down on the back cover of your phone and slide it away from the camera.

Aggiungi Commento

You can now remove the battery by prying it up with your finger. You can now remove the battery by prying it up with your finger.
  • You can now remove the battery by prying it up with your finger.

Aggiungi Commento

Use a plastic opening tool to carefully pry the back cover surrounding the camera up from the phone.
  • Use a plastic opening tool to carefully pry the back cover surrounding the camera up from the phone.

Aggiungi Commento

Remove the five 3.4mm Philips screws securing the backing of the phone.
  • Remove the five 3.4mm Philips screws securing the backing of the phone.

Aggiungi Commento

Use a plastic opening tool to carefully pry off the back cover. Make sure you are prying along the edge and not between the two halves of the phone that slide away from each other. Be careful to not drop the volume changing piece, for it can easily slip out.
  • Use a plastic opening tool to carefully pry off the back cover.

  • Make sure you are prying along the edge and not between the two halves of the phone that slide away from each other.

  • Be careful to not drop the volume changing piece, for it can easily slip out.

Aggiungi Commento

Remove the two 3.45 mm Philips screws below the white sticker.
  • Remove the two 3.45 mm Philips screws below the white sticker.

Aggiungi Commento

Carefully lift the motherboard up from the bottom edge. The film of wires is still attached to the motherboard, so do not completely remove the motherboard just yet or you may damage it.
  • Carefully lift the motherboard up from the bottom edge.

  • The film of wires is still attached to the motherboard, so do not completely remove the motherboard just yet or you may damage it.

Aggiungi Commento

Use a plastic opening tool to disconnect the film from the motherboard. Use a plastic opening tool to disconnect the film from the motherboard.
  • Use a plastic opening tool to disconnect the film from the motherboard.

Aggiungi Commento

Remove the eight 1.7mm Philips screws above the keyboard.
  • Remove the eight 1.7mm Philips screws above the keyboard.

Aggiungi Commento

Carefully remove the keyboard frame from the sliding mechanisms underneath.
  • Carefully remove the keyboard frame from the sliding mechanisms underneath.

Aggiungi Commento

Remove the five 3.0mm Philips screws around the outside of the sliding mechanisms.
  • Remove the five 3.0mm Philips screws around the outside of the sliding mechanisms.

Aggiungi Commento

Use a plastic opening tool to pry off the upper slide plate. Be careful of the film of wires when taking off the upper slide plate. Be careful of the film of wires when taking off the upper slide plate.
  • Use a plastic opening tool to pry off the upper slide plate.

  • Be careful of the film of wires when taking off the upper slide plate.

Aggiungi Commento

Use tweezers to open the four black gates by putting them in the "up" position. With the same tweezers, carefully pull out the orange strips from the four specified gates. With the same tweezers, carefully pull out the orange strips from the four specified gates.
  • Use tweezers to open the four black gates by putting them in the "up" position.

  • With the same tweezers, carefully pull out the orange strips from the four specified gates.

Aggiungi Commento

Using tweezers, gently remove the bottom orange strip from the device Using tweezers, gently remove the bottom orange strip from the device
  • Using tweezers, gently remove the bottom orange strip from the device

Aggiungi Commento

In this procedure, the rubber function key pad can easily fall out, so it would be best to take it out and set it safely aside. In this procedure, the rubber function key pad can easily fall out, so it would be best to take it out and set it safely aside.
  • In this procedure, the rubber function key pad can easily fall out, so it would be best to take it out and set it safely aside.

Aggiungi Commento

Starting at the top, use a plastic opening tool to pry open the protective screen on the front of the phone. One of the strips you pulled out of a gate from a previous step is attached to the screen at the bottom. Be careful not to damage it when you are taking off the screen. The protective screen is glued underneath the edges, so it will be a little more difficult to get off.
  • Starting at the top, use a plastic opening tool to pry open the protective screen on the front of the phone.

  • One of the strips you pulled out of a gate from a previous step is attached to the screen at the bottom. Be careful not to damage it when you are taking off the screen.

  • The protective screen is glued underneath the edges, so it will be a little more difficult to get off.

  • Keep your hand underneath the OLED screen at all times because it easily falls out once the protective screen detaches.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Team

Cal Poly, Team 7-32, Maness Spring 2012 Membro di Cal Poly, Team 7-32, Maness Spring 2012

CPSU-MANESS-S12S7G32

4 Membri

16 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 1,855