Introduzione

This guide shows all the steps leading up to, and including, removing the speaker so that a new one can be installed.

Apply pressure to the back cover and slide it forward towards the camera.
  • Apply pressure to the back cover and slide it forward towards the camera.

  • Lift the back cover off the phone.

Aggiungi Commento

Holding the phone firmly, use the notches to grip and lift up the battery.
  • Holding the phone firmly, use the notches to grip and lift up the battery.

Aggiungi Commento

Remove the four 4.45mm screws at the corners of the phone.
  • Remove the four 4.45mm screws at the corners of the phone.

Aggiungi Commento

Use the plastic opening tool to unhinge the locks around the edges of the phone. Do not worry about the inner components of the phone; they are not connected to this case.
  • Use the plastic opening tool to unhinge the locks around the edges of the phone.

  • Do not worry about the inner components of the phone; they are not connected to this case.

Aggiungi Commento

Lift the casing off of the phone.
  • Lift the casing off of the phone.

Aggiungi Commento

With the screws removed, locate the antenna.
  • With the screws removed, locate the antenna.

Aggiungi Commento

Kit RAM Mac
Accelera il Mac. Porta la memoria al massimo.
Kit RAM Mac
Metti più memoria nel tuo Mac.
Using a Phillips head screwdriver, remove the 4.50mm screw holding the antenna in place.
  • Using a Phillips head screwdriver, remove the 4.50mm screw holding the antenna in place.

Aggiungi Commento

Using the plastic opener tool, squeeze gently on the antenna cable connector and lift to remove the connector from its position.
  • Using the plastic opener tool, squeeze gently on the antenna cable connector and lift to remove the connector from its position.

Aggiungi Commento

Gently lift up on the antenna and remove it from the back of the device.
  • Gently lift up on the antenna and remove it from the back of the device.

Aggiungi Commento

Remove the two 3.50mm screws connecting the motherboard to the case.
  • Remove the two 3.50mm screws connecting the motherboard to the case.

Aggiungi Commento

Use the plastic opener tool to detach the three ribbons on the motherboard. Use the plastic opener tool to detach the three ribbons on the motherboard. Use the plastic opener tool to detach the three ribbons on the motherboard.
  • Use the plastic opener tool to detach the three ribbons on the motherboard.

Aggiungi Commento

Lift out the top right ribbon from its slot on the motherboard.
  • Lift out the top right ribbon from its slot on the motherboard.

Aggiungi Commento

Use the plastic opener tool to unhinge the the locks on the side of the motherboard connecting it to the front casing. Use the plastic opener tool to unhinge the the locks on the side of the motherboard connecting it to the front casing.
  • Use the plastic opener tool to unhinge the the locks on the side of the motherboard connecting it to the front casing.

Aggiungi Commento

Lift the motherboard away from the front casing.
  • Lift the motherboard away from the front casing.

Aggiungi Commento

After removing lifting up on the motherboard, the front casing and center frame should be separated as shown.
  • After removing lifting up on the motherboard, the front casing and center frame should be separated as shown.

Aggiungi Commento

Using tweezers to grasp the pins of the speaker, gently lift the speaker up out of its setting in the front case.
  • Using tweezers to grasp the pins of the speaker, gently lift the speaker up out of its setting in the front case.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Brayton

Membro da: 12/10/2011

40 Reputazione

4 Guide realizzate

Team

Cal Poly, Team 3-13, Regan Fall 2011 Membro di Cal Poly, Team 3-13, Regan Fall 2011

CPSU-REGAN-F11S3G13

4 Membri

16 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 706