Introduzione

Use this guide to replace the rear-facing camera assembly in your Samsung Galaxy Note II.

Grasp the end of the stylus and remove it from its slot in the midframe. Grasp the end of the stylus and remove it from its slot in the midframe.
  • Grasp the end of the stylus and remove it from its slot in the midframe.

Aggiungi Commento

Pry with a plastic opening tool, or your fingernail, in the divot to the left of the rear-facing camera, near the power button. Pry with a plastic opening tool, or your fingernail, in the divot to the left of the rear-facing camera, near the power button.
  • Pry with a plastic opening tool, or your fingernail, in the divot to the left of the rear-facing camera, near the power button.

Aggiungi Commento

Lift the rear case by the corner nearest the divot and remove it from the phone. Lift the rear case by the corner nearest the divot and remove it from the phone. Lift the rear case by the corner nearest the divot and remove it from the phone.
  • Lift the rear case by the corner nearest the divot and remove it from the phone.

Aggiungi Commento

If you have an SD card inserted, use the flat end of a spudger, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click. After the click, release the card and it will pop out of its slot. Remove the microSD card.
  • If you have an SD card inserted, use the flat end of a spudger, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.

  • After the click, release the card and it will pop out of its slot.

  • Remove the microSD card.

  • For reassembly, push the microSD card into the slot until it clicks in place.

Aggiungi Commento

Insert a plastic opening tool, or your finger, into the notch of the battery compartment and lift the battery upward. Insert a plastic opening tool, or your finger, into the notch of the battery compartment and lift the battery upward.
  • Insert a plastic opening tool, or your finger, into the notch of the battery compartment and lift the battery upward.

Aggiungi Commento

Remove the battery from the midframe.
  • Remove the battery from the midframe.

Aggiungi Commento

Remove the eleven 4.0 mm Phillips #00 screws securing the midframe to the display assembly.
  • Remove the eleven 4.0 mm Phillips #00 screws securing the midframe to the display assembly.

In my phone some of the screws are litterally not ot turn - I screwed up one of the heads - be careful!

erich zalcmann - Replica

I have 2 note 2 phones model #: SGH-I317M. I have a broken screen that does not display in my note 2 but my brother's note 2 is working perfectly. Can I either transfer the motherboard in MY note 2 to my brothers note 2 or swap the broken screen with the new screen in my brother's note 2 ? Thanks. Reach me at anmac1789@gmail.com

An Mac - Replica

Insert your plastic opening tool between the midframe and front panel assembly on the side of the phone. Slide the plastic opening tool down the seam. Slide the plastic opening tool down the seam.
  • Insert your plastic opening tool between the midframe and front panel assembly on the side of the phone.

  • Slide the plastic opening tool down the seam.

I didn't have an opening tool, so I used a stiff guitar pick. Worked like a charm.

evanjpederson - Replica

for best result without any scratches or breaking frame, open the frame on table (solid), don't open on hand.

Chovav Sutachy - Replica

Continue to run the plastic opening tool down the seam. Continue to run the plastic opening tool down the seam. Continue to run the plastic opening tool down the seam.
  • Continue to run the plastic opening tool down the seam.

Aggiungi Commento

Carefully pry around the corner with a plastic opening tool. Carefully pry around the corner with a plastic opening tool.
  • Carefully pry around the corner with a plastic opening tool.

The screen cracked using that plastic tool.

hell0allis0n - Replica

Pry along the top of the phone with a plastic opening tool. Pry along the top of the phone with a plastic opening tool.
  • Pry along the top of the phone with a plastic opening tool.

Aggiungi Commento

Push the plastic opening tool down to free the corner of the midframe from the display assembly. Push the plastic opening tool down to free the corner of the midframe from the display assembly.
  • Push the plastic opening tool down to free the corner of the midframe from the display assembly.

Aggiungi Commento

Free the clips along the power button side of the phone. Lastly, free the two clips along the top and bottom edge of battery compartment.
  • Free the clips along the power button side of the phone.

  • Lastly, free the two clips along the top and bottom edge of battery compartment.

Start with the top clip. You can see it located next to the three battery connectors. Insert the spludge from the side gently to push, the clip should go off.

Once this clip is off, the bottom battery clip can be unclipped simply by gently moving the two pieces apart.

anonymous 4780 - Replica

Gan kalok bluetooth hp saya sama wifi nya nggak bisa nelusurin jaringan apa nya yg rusak apa gara gara udah di root

aryadana55 -

If you're primarily following the pictures, as I was, you might be frustrated that your display assembly isn't popping off. Unfortunately, a vital step was listed in the instructions but not photographed:

"Lastly, there are two clips along the top and bottom edge of battery compartment that also hold the display assembly in place."

alimac70117 - Replica

Lift the display assembly out of the midframe. Lift the display assembly out of the midframe.
  • Lift the display assembly out of the midframe.

unblock the edge at the middle-up of the battery compart!

Giorgio - Replica

Use a spudger to disconnect the vibrator/power button assembly cable connector. Disconnect the antenna cable connector. Disconnect the display cable connector.
  • Use a spudger to disconnect the vibrator/power button assembly cable connector.

  • Disconnect the antenna cable connector.

  • Disconnect the display cable connector.

Dear Sirs,

My Galaxy Note II is completely dead due to lightning in the house. I guess there is a fuse or a protection somewhere but I can not find it. Can you help ? Thanks in advance, Jose

Jose - Replica

One idea would be to track backwards, i.e. check to see if current is reaching from the charge port to the mainboard. Looking at the following picture http://d3nevzfk7ii3be.cloudfront.net/igi... it seems like the fuse is - as expected - located right by the USB port. If you're lucky it could be as easy as replacing the charging board, a $10 component.

hakro807 -

My Note II LTE does not have the antenna cable like here

Bubbele - Replica

Disconnect the front-facing camera cable connector. Disconnect the headphone jack cable connector. Disconnect the digitizer cable connector.
  • Disconnect the front-facing camera cable connector.

  • Disconnect the headphone jack cable connector.

  • Disconnect the digitizer cable connector.

Aggiungi Commento

Use the spudger to disconnect the antenna cable connector from the motherboard. Disconnect the soft button cable connector. Disconnect the USB board cable connector.
  • Use the spudger to disconnect the antenna cable connector from the motherboard.

  • Disconnect the soft button cable connector.

  • Disconnect the USB board cable connector.

Aggiungi Commento

Remove the 3 mm Phillips #00 screw securing the motherboard to the display assembly.
  • Remove the 3 mm Phillips #00 screw securing the motherboard to the display assembly.

Is it possible to replace my Note II N7105 motherboard to N7100? Is there some negative effects happen, if i did it?

Eduardo Lucas III - Replica

Gently remove the motherboard. Hold the motherboard by its edges to prevent ESD damage. Be careful not to snag it on any cables as you extract it from the display assembly.
  • Gently remove the motherboard.

  • Hold the motherboard by its edges to prevent ESD damage. Be careful not to snag it on any cables as you extract it from the display assembly.

Aggiungi Commento

Use a spudger to disconnect the rear-facing camera assembly cable connector.
  • Use a spudger to disconnect the rear-facing camera assembly cable connector.

Aggiungi Commento

Use tweezers, or your fingers, to remove the rear-facing camera assembly.
  • Use tweezers, or your fingers, to remove the rear-facing camera assembly.

Bang kalau sering panas terus mati sendiri nanti panasnya dingin nyala layani tanpa di pegang lampunya redup kayak hp..... Yang kacannya lama warna...pudar...tapi jelas..Nanti terang sendiri.... Itu apanya ya bang....servis.... Nanya dulu berapa ongkosnya.... Sekali lagi saya nanya dulu..... Ya bang....

Hamba Allah - Replica

Sekali lagi saya nanya dulu ya bang servis....

Hamba Allah - Replica

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 13 persone hanno completato questa guida.

Sam Lionheart

Membro da: 18/10/2012

323.757 Reputazione

1.664 Guide realizzate

Team

iFixit Membro di iFixit

Community

113 Membri

6.002 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 10

Ultimi 30 Giorni: 55

Tutti i Tempi: 11,114