Introduzione

Use this guide to replace the front panel display assembly in your Samsung Galaxy Note.

Grasp the cap of the stylus and remove it from its slot in the midframe. Grasp the cap of the stylus and remove it from its slot in the midframe.
  • Grasp the cap of the stylus and remove it from its slot in the midframe.

Aggiungi Commento

Pry with a plastic opening tool, or your fingernail, in the divot to the right of the rear-facing camera, near the volume rocker. Pry with a plastic opening tool, or your fingernail, in the divot to the right of the rear-facing camera, near the volume rocker.
  • Pry with a plastic opening tool, or your fingernail, in the divot to the right of the rear-facing camera, near the volume rocker.

Aggiungi Commento

Lift and remove the rear case from the phone. Lift and remove the rear case from the phone.
  • Lift and remove the rear case from the phone.

Aggiungi Commento

Insert your finger in the notch of the battery compartment. Press the battery toward the rear facing camera while pulling outward.
  • Insert your finger in the notch of the battery compartment.

  • Press the battery toward the rear facing camera while pulling outward.

Aggiungi Commento

Use the flat end of a spudger, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click. After the click, release the card and it will pop out of its slot. For reassembly, push the microSD card into the slot until it clicks in place.
  • Use the flat end of a spudger, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.

  • After the click, release the card and it will pop out of its slot.

  • For reassembly, push the microSD card into the slot until it clicks in place.

Aggiungi Commento

Remove the microSD card from its slot in the midframe.
  • Remove the microSD card from its slot in the midframe.

Aggiungi Commento

Use a plastic opening tool, or your fingernail, to push the SIM card out of its compartment. Use a plastic opening tool, or your fingernail, to push the SIM card out of its compartment.
  • Use a plastic opening tool, or your fingernail, to push the SIM card out of its compartment.

Aggiungi Commento

Slide the SIM card out the rest of the way with your thumb and remove it from the device. Slide the SIM card out the rest of the way with your thumb and remove it from the device.
  • Slide the SIM card out the rest of the way with your thumb and remove it from the device.

Aggiungi Commento

Remove the nine 3.4 mm Phillips #00 screws securing the midframe to the display assembly.
  • Remove the nine 3.4 mm Phillips #00 screws securing the midframe to the display assembly.

Aggiungi Commento

Insert your plastic opening tool to the left of the power button between the midframe and the front panel assembly and pry. Insert your plastic opening tool to the left of the power button between the midframe and the front panel assembly and pry.
  • Insert your plastic opening tool to the left of the power button between the midframe and the front panel assembly and pry.

Aggiungi Commento

Slide the plastic opening tool down the seam. Slide the plastic opening tool down the seam. Slide the plastic opening tool down the seam.
  • Slide the plastic opening tool down the seam.

Aggiungi Commento

Insert your plastic opening tool to the left of the headphone jack between the midframe and the display assembly. Slide the opening tool along the top edge of the phone. Continue to run the plastic opening tool around the perimeter of the phone until the midframe is separated.
  • Insert your plastic opening tool to the left of the headphone jack between the midframe and the display assembly.

  • Slide the opening tool along the top edge of the phone.

  • Continue to run the plastic opening tool around the perimeter of the phone until the midframe is separated.

Aggiungi Commento

Remove the midframe from the display assembly. Remove the midframe from the display assembly.
  • Remove the midframe from the display assembly.

Aggiungi Commento

Use the flat end of a spudger to carefully disconnect the display cable connector. Use the flat end of a spudger to carefully disconnect the display cable connector.
  • Use the flat end of a spudger to carefully disconnect the display cable connector.

Aggiungi Commento

Use a spudger to disconnect the front-facing camera assembly cable connector. Disconnect the headphone jack/earpiece speaker assembly cable connector. Disconnect the digitizer cable connector.
  • Use a spudger to disconnect the front-facing camera assembly cable connector.

  • Disconnect the headphone jack/earpiece speaker assembly cable connector.

  • Disconnect the digitizer cable connector.

Aggiungi Commento

Disconnect the soft button cable connector with the flat end of a spudger. Use a spudger to disconnect the USB board cable connector. Disconnect the antenna cable connector.
  • Disconnect the soft button cable connector with the flat end of a spudger.

  • Use a spudger to disconnect the USB board cable connector.

  • Disconnect the antenna cable connector.

Aggiungi Commento

Remove the two 3.4 mm Phillips #00 screws securing the motherboard to the display assembly.
  • Remove the two 3.4 mm Phillips #00 screws securing the motherboard to the display assembly.

Aggiungi Commento

Remove the motherboard assembly from the display assembly. Remove the motherboard assembly from the display assembly.
  • Remove the motherboard assembly from the display assembly.

Aggiungi Commento

Remove the two 3 mm Phillips #00 screws securing the upper display assembly bracket.
  • Remove the two 3 mm Phillips #00 screws securing the upper display assembly bracket.

Aggiungi Commento

Use a pair of tweezers, or your fingers, to remove the upper display assembly bracket. Use a pair of tweezers, or your fingers, to remove the upper display assembly bracket.
  • Use a pair of tweezers, or your fingers, to remove the upper display assembly bracket.

Aggiungi Commento

Using tweezers, or your fingers, remove the front-facing camera assembly.
  • Using tweezers, or your fingers, remove the front-facing camera assembly.

Aggiungi Commento

Use the tip of a spudger to pry the headphone jack/earpiece speaker assembly out of its recess in the display assembly. Use the tip of a spudger to pry the headphone jack/earpiece speaker assembly out of its recess in the display assembly.
  • Use the tip of a spudger to pry the headphone jack/earpiece speaker assembly out of its recess in the display assembly.

Aggiungi Commento

Use tweezers, or your fingers, to remove the headphone jack/earpiece speaker assembly.
  • Use tweezers, or your fingers, to remove the headphone jack/earpiece speaker assembly.

Aggiungi Commento

Remove the three 3 mm Phillips #00 screws securing the speaker enclosure to the front panel assembly.
  • Remove the three 3 mm Phillips #00 screws securing the speaker enclosure to the front panel assembly.

Aggiungi Commento

Lift the speaker enclosure from the display assembly.
  • Lift the speaker enclosure from the display assembly.

Aggiungi Commento

Use the tip of a spudger to disconnect the antenna cable connector from the USB board. Remove the antenna cable.
  • Use the tip of a spudger to disconnect the antenna cable connector from the USB board.

  • Remove the antenna cable.

Aggiungi Commento

Push the flat end of a spudger under the USB board to separate it from the display assembly. Insert the spudger at a shallow angle to avoid bending or damaging the USB board. Insert the spudger at a shallow angle to avoid bending or damaging the USB board.
  • Push the flat end of a spudger under the USB board to separate it from the display assembly.

  • Insert the spudger at a shallow angle to avoid bending or damaging the USB board.

Aggiungi Commento

Remove the USB board.
  • Remove the USB board.

Aggiungi Commento

Insert the tip of a spudger under the vibrator connector cable near the contacts then slide toward the vibrator itself. Insert the tip of a spudger under the vibrator connector cable near the contacts then slide toward the vibrator itself. Insert the tip of a spudger under the vibrator connector cable near the contacts then slide toward the vibrator itself.
  • Insert the tip of a spudger under the vibrator connector cable near the contacts then slide toward the vibrator itself.

Aggiungi Commento

Insert the flat end of a spudger under the vibrator connector cable, and pry it up from the adhesive. Insert the flat end of a spudger under the vibrator connector cable, and pry it up from the adhesive.
  • Insert the flat end of a spudger under the vibrator connector cable, and pry it up from the adhesive.

Aggiungi Commento

Remove the vibrator from the display assembly.
  • Remove the vibrator from the display assembly.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 35 persone hanno completato questa guida.

Sam Lionheart

Membro da: 18/10/2012

323.778 Reputazione

1.664 Guide realizzate

Team

iFixit Membro di iFixit

Community

113 Membri

6.002 Guide realizzate

étape 31 ensuite ??

Fabrice - Replica

i have a galaxy not and its display is badly broken,at the top of the phone(front side),the display is broken so badly that i am able to a little circuit i.e. a brown color wire which is connected to the display.

so my ques. is that can the phone work after repairing or it has gone?

Abhishek Kumbhar - Replica

Hello Abhishek Kumbhar, if the motherboard is not damaged it's all fine. All other parts are replaceable

Georg Fischer - Replica

excellent photos

of samsung 717

murali maroju - Replica

i am trying to get my phone to charge but its not and i have it pluged in and it doesnt want to charge

Anthany Kleven - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 7

Ultimi 7 Giorni: 38

Ultimi 30 Giorni: 190

Tutti i Tempi: 40,991