Strumenti

Nessun attrezzo richiesto.

Parti

Nessuna parte richiesta.

Begin by turn the device over to it's back, with the screen facing down.
  • Begin by turn the device over to it's back, with the screen facing down.

Aggiungi Commento

At the top of the device there is a small notch that is used to remove the battery door. Using a pry tool or your fingernail, pry off the battery door from the main housing.
  • At the top of the device there is a small notch that is used to remove the battery door.

  • Using a pry tool or your fingernail, pry off the battery door from the main housing.

Aggiungi Commento

Place the battery door to the side. Using a pry tool or your fingernail, pry the battery up towards you. You have now removed the battery!
  • Place the battery door to the side.

  • Using a pry tool or your fingernail, pry the battery up towards you.

  • You have now removed the battery!

Aggiungi Commento

Make sure when replacing the battery that the arrow on the bottom is facing down.
  • Make sure when replacing the battery that the arrow on the bottom is facing down.

Aggiungi Commento

Remove the 6 Phillips head screws that hold the rear housing in place.
  • Remove the 6 Phillips head screws that hold the rear housing in place.

Aggiungi Commento

Using a spudger or plastic pry tool, slowly go around the phone between the display & rear housing to release the clips.
  • Using a spudger or plastic pry tool, slowly go around the phone between the display & rear housing to release the clips.

Aggiungi Commento

Lift the rear housing from the display assembly.
  • Lift the rear housing from the display assembly.

Aggiungi Commento

Using your spudger/plastic pry tool, disconnect the headphone jack flex cable. Using your spudger/plastic pry tool, disconnect the headphone jack flex cable.
  • Using your spudger/plastic pry tool, disconnect the headphone jack flex cable.

Aggiungi Commento

Using your spudger/plastic pry tool, disconnect the rear speaker flex cable. Using your spudger/plastic pry tool, disconnect the rear speaker flex cable.
  • Using your spudger/plastic pry tool, disconnect the rear speaker flex cable.

Aggiungi Commento

Using a spudger/pry tool, carefully remove the vibration motor from its housing. This has a mild adhesive on the bottom.
  • Using a spudger/pry tool, carefully remove the vibration motor from its housing. This has a mild adhesive on the bottom.

Aggiungi Commento

After removing both flex cables, slowly move the logic board to the left of the screen assembly. Do not try and remove the logic board all the way, as you still have to remove the display assembly flex cable!
  • After removing both flex cables, slowly move the logic board to the left of the screen assembly.

  • Do not try and remove the logic board all the way, as you still have to remove the display assembly flex cable!

Aggiungi Commento

Using your spudger/plastic pry tool, disconnect the LCD/Digitizer flex cable.
  • Using your spudger/plastic pry tool, disconnect the LCD/Digitizer flex cable.

Aggiungi Commento

You have now removed the logic board from the display assembly. You have now removed the logic board from the display assembly.
  • You have now removed the logic board from the display assembly.

Aggiungi Commento

Using a spudger/plastic pry tool lift the brown ZIF tab on the front-facing camera connector.
  • Using a spudger/plastic pry tool lift the brown ZIF tab on the front-facing camera connector.

  • Do not pry at the black part, as this will damage the connector on the board.

Aggiungi Commento

Carefully pull the camera out of it's connector and set to the side.
  • Carefully pull the camera out of it's connector and set to the side.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 3 persone hanno completato questa guida.

Josh Forester

Membro da: 28/11/2010

2.294 Reputazione

10 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 1

Tutti i Tempi: 140