Introduzione

How to remove and replace the hard drive.

Parti

Nessuna parte richiesta.

Remove the 7 mm Philip screws.
  • Remove the 7 mm Philip screws.

  • Remove the 10 mm Philip screws.

  • Remove the 14 mm Philip screw.

Aggiungi Commento

Open the flap on the left hand side. Open the flap on the left hand side.
  • Open the flap on the left hand side.

Aggiungi Commento

Insert the iPod opening tools between the right and left sides of the latch. Pry the right side  of the latch, and then pry the left side to detach the laptop's cover.
  • Insert the iPod opening tools between the right and left sides of the latch.

  • Pry the right side of the latch, and then pry the left side to detach the laptop's cover.

Aggiungi Commento

Open the flap on the right side. Open the flap on the right side.
  • Open the flap on the right side.

Aggiungi Commento

Insert the iPod opening tools towards the right side of the latch.
  • Insert the iPod opening tools towards the right side of the latch.

  • Gently pry the right side out to release the top cover.

Aggiungi Commento

Lift the keyboard slowly. A cable connects the keyboard to the motherboard. If you are not careful, you will damage the cable.
  • Lift the keyboard slowly.

  • A cable connects the keyboard to the motherboard. If you are not careful, you will damage the cable.

Aggiungi Commento

Use your fingers or a spudger to detach the connector.
  • Use your fingers or a spudger to detach the connector.

Aggiungi Commento

Carefully lift and remove the keyboard. Carefully lift and remove the keyboard.
  • Carefully lift and remove the keyboard.

Aggiungi Commento

On the back of the computer, use a Flathead screwdriver to remove this lone screw.
  • On the back of the computer, use a Flathead screwdriver to remove this lone screw.

Aggiungi Commento

After the screw is out, gently remove the cover. After the screw is out, gently remove the cover.
  • After the screw is out, gently remove the cover.

Aggiungi Commento

Turn the computer back over so the hard drive faces up. Remove the shown screw with a Phillips screwdriver. Turn the computer back over so the hard drive faces up. Remove the shown screw with a Phillips screwdriver. Turn the computer back over so the hard drive faces up. Remove the shown screw with a Phillips screwdriver.
  • Turn the computer back over so the hard drive faces up. Remove the shown screw with a Phillips screwdriver.

Aggiungi Commento

Make sure you are grounded and detach the IDA cable connecting the hard disk to the motherboard.
  • Make sure you are grounded and detach the IDA cable connecting the hard disk to the motherboard.

Aggiungi Commento

Remove the final two screws (shown) and slide out the hard drive. Remove the final two screws (shown) and slide out the hard drive.
  • Remove the final two screws (shown) and slide out the hard drive.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Derek Driscoll

Membro da: 15/04/2010

110 Reputazione

16 Guide realizzate

Team

Cal Poly, Team 26-27, Regan Spring 2010 Membro di Cal Poly, Team 26-27, Regan Spring 2010

CPSU-REGAN-S10S26G27

3 Membri

18 Guide realizzate

You don't have to go to this length to remove the hard drive on a 560Z. Only do steps 0 (remove battery), 9 (remove screw) and 10 (remove cover). Then simply grab the blue tab of the hard drive caddy and pull the drive out of the bay. Complete directions on maintenance of the IBM Thinkpad 560Z can be found here:

http://www.thinkpads.com/support/hmm/hmm...

The Hardware Maintenance Manual has all of the information you need to take a 560Z apart and put it back together.

The procedure outlined here is similar to what the 560, 560E and 560X systems required; the 560Z is totally different when removing the hard drive.

Raymond - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 7

Tutti i Tempi: 2,471