Parti

Nessuna parte richiesta.

Open the tray by pressing the eject button Remove the DVD tray faceplate by pushing the faceplate up off of the tray. Remove the DVD tray faceplate by pushing the faceplate up off of the tray.
  • Open the tray by pressing the eject button

  • Remove the DVD tray faceplate by pushing the faceplate up off of the tray.

Aggiungi Commento

Press the eject button to insert the tray
  • Press the eject button to insert the tray

  • After the tray is closed unplug DVD player

Aggiungi Commento

Unscrew the 3 screws in the back.
  • Unscrew the 3 screws in the back.

Aggiungi Commento

Pull the outer case upward and then towards you. Pull the outer case upward and then towards you.
  • Pull the outer case upward and then towards you.

Aggiungi Commento

There are six symmetrically placed tabs holding in the front faceplate.  Unhook these six tabs to loosen the faceplate. There are six symmetrically placed tabs holding in the front faceplate.  Unhook these six tabs to loosen the faceplate. There are six symmetrically placed tabs holding in the front faceplate.  Unhook these six tabs to loosen the faceplate.
  • There are six symmetrically placed tabs holding in the front faceplate. Unhook these six tabs to loosen the faceplate.

Aggiungi Commento

Pull off front faceplate. This may take a couple of tries to get all six tabs unhooked simultaneously. Pull off front faceplate. This may take a couple of tries to get all six tabs unhooked simultaneously.
  • Pull off front faceplate. This may take a couple of tries to get all six tabs unhooked simultaneously.

Aggiungi Commento

Locate the white clip that attaches the cord to the motherboard Grasp clip and squeeze to release Lift up and remove power cord
  • Locate the white clip that attaches the cord to the motherboard

  • Grasp clip and squeeze to release

  • Lift up and remove power cord

  • Slide cord mount from outer case

Aggiungi Commento

Remove the three screws holding in the DVD tray Remove the three screws holding in the DVD tray Remove the three screws holding in the DVD tray
  • Remove the three screws holding in the DVD tray

Aggiungi Commento

Remove the power cord and first two ribbons by pulling them directly out of their sockets. Remove the power cord and first two ribbons by pulling them directly out of their sockets.
  • Remove the power cord and first two ribbons by pulling them directly out of their sockets.

Aggiungi Commento

Gently lift the DVD tray off of the motherboard. Gently lift the DVD tray off of the motherboard.
  • Gently lift the DVD tray off of the motherboard.

Aggiungi Commento

Unscrew the 2 screws on the motherboard Unscrew the 2 screws on the back
  • Unscrew the 2 screws on the motherboard

  • Unscrew the 2 screws on the back

Aggiungi Commento

Disconnect the wires and ribbon by pulling them out of their respective connections Disconnect the wires and ribbon by pulling them out of their respective connections Disconnect the wires and ribbon by pulling them out of their respective connections
  • Disconnect the wires and ribbon by pulling them out of their respective connections

Aggiungi Commento

Lift board up and out of the lower case Lift board up and out of the lower case
  • Lift board up and out of the lower case

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Mitchell Hart

Membro da: 21/01/2011

819 Reputazione

5 Guide realizzate

Team

Cal Poly, Team 3-30, Regan Winter 2011 Membro di Cal Poly, Team 3-30, Regan Winter 2011

CPSU-REGAN-W11S3G30

4 Membri

8 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 4

Ultimi 30 Giorni: 7

Tutti i Tempi: 2,768