Parti

Nessuna parte richiesta.

Turn bike upside down as shown
  • Turn bike upside down as shown

Aggiungi Commento

Use a wrench to loosen the nut holding the wheel's axle on one side. Once it's loose enough, continue removing the nut with your hand. After removing the nut, also remove the washer under it.
  • Use a wrench to loosen the nut holding the wheel's axle on one side.

    • Once it's loose enough, continue removing the nut with your hand.

    • After removing the nut, also remove the washer under it.

  • Note how the washer has a small appendage that locks into a slot in the fork.

Aggiungi Commento

Do the same for the nut on the other side.
  • Do the same for the nut on the other side.

Aggiungi Commento

Now simply lift the wheel up and out of the fork.
  • Now simply lift the wheel up and out of the fork.

Aggiungi Commento

Unscrew cap from air valve. Use a thin object to press down the pin in the center of the valve, releasing the air in the tire.
  • Unscrew cap from air valve.

  • Use a thin object to press down the pin in the center of the valve, releasing the air in the tire.

    • Note: We use a hex wrench in this picture, but you can use pretty much any blunt object that fits.

Aggiungi Commento

Take a tire lever, and wedge it between the tire and the rim. Make sure the end scoops inward to grab the tire. Once you manage to grab the edge of the tire with the lever, pull the lever back to scoop the tire out of the rim. Then, use the notch in the other end of the lever to keep it steadily anchored on a nearby spoke.
  • Take a tire lever, and wedge it between the tire and the rim. Make sure the end scoops inward to grab the tire.

  • Once you manage to grab the edge of the tire with the lever, pull the lever back to scoop the tire out of the rim.

  • Then, use the notch in the other end of the lever to keep it steadily anchored on a nearby spoke.

Aggiungi Commento

Do the same thing with another tire lever about 5 inches away from the first. Do the same thing with another tire lever about 5 inches away from the first.
  • Do the same thing with another tire lever about 5 inches away from the first.

Aggiungi Commento

Do the same with a third tire lever even farther around the tire. Then, leapfrog the second and third levers until the tire comes partway off. Then, leapfrog the second and third levers until the tire comes partway off.
  • Do the same with a third tire lever even farther around the tire.

  • Then, leapfrog the second and third levers until the tire comes partway off.

Aggiungi Commento

Now, use the tire levers to wedge the tire off the other rim. This will be far easier than for the first rim. As you do this, make sure you pull the air valve out through its hole in the rim. Now, the tire (with the tube inside) should be completely removed from the rim.
  • Now, use the tire levers to wedge the tire off the other rim. This will be far easier than for the first rim.

    • As you do this, make sure you pull the air valve out through its hole in the rim.

  • Now, the tire (with the tube inside) should be completely removed from the rim.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Tobias Elder

Membro da: 25/04/2013

113 Reputazione

7 Guide realizzate

Team

Cal Poly, Team 21-53, Johann Spring 2013 Membro di Cal Poly, Team 21-53, Johann Spring 2013

CPSU-JOHANN-S13S21G53

4 Membri

7 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 2

Tutti i Tempi: 552