Introduzione

The front casing is the frontal frame on your Panasonic Lumix DMC-TZ5. All the major components of the camera are attached to this front casing.

Parti

Nessuna parte richiesta.

Remove the battery and memory card from the device.
  • Remove the battery and memory card from the device.

Aggiungi Commento

Remove 4 screws from the right side of the camera.
  • Remove 4 screws from the right side of the camera.

    • There are two 3.4mm screws at the top.

    • There are two 2.2mm screws at the bottom.

Aggiungi Commento

Remove the single 3.4mm screw on the left side of the camera.
  • Remove the single 3.4mm screw on the left side of the camera.

Aggiungi Commento

Remove 5 screws from the base of the camera.
  • Remove 5 screws from the base of the camera.

    • There are two 2.2mm screws next to the battery compartment.

    • There are three 4mm screws around the tripod mount.

Aggiungi Commento

Slowly slide the back cover away from the device
  • Slowly slide the back cover away from the device

    • The back casing is held in place by two ribbon cables. Do not pull the back cover too far from the camera.

Aggiungi Commento

Detach both ribbon cables using a spudger. Use the tip of the spudger to lift the black clip upward, unlocking the ribbon cable.
  • Detach both ribbon cables using a spudger.

    • Use the tip of the spudger to lift the black clip upward, unlocking the ribbon cable.

Aggiungi Commento

Remove the back casing from the camera.
  • Remove the back casing from the camera.

Aggiungi Commento

Use the spudger to remove the ribbon cable connecting the lens casing to the circuit board by lifting up the black clip. Carefully remove the function switch cover. This unit snaps on and off.
  • Use the spudger to remove the ribbon cable connecting the lens casing to the circuit board by lifting up the black clip.

  • Carefully remove the function switch cover. This unit snaps on and off.

Aggiungi Commento

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Carefully unsnap the front logic board from the rear logic board using a spudger.
  • Carefully unsnap the front logic board from the rear logic board using a spudger.

Aggiungi Commento

Slide the entire top part of the camera that is attached to the logic board, horizontally away from the camera. Slide the entire top part of the camera that is attached to the logic board, horizontally away from the camera.
  • Slide the entire top part of the camera that is attached to the logic board, horizontally away from the camera.

Aggiungi Commento

Remove the ribbon cable from the top connection panel by unlocking the black clip with a spudger. This leaves you with the logic board and the top connection panel separate and free from the camera This leaves you with the logic board and the top connection panel separate and free from the camera
  • Remove the ribbon cable from the top connection panel by unlocking the black clip with a spudger.

  • This leaves you with the logic board and the top connection panel separate and free from the camera

Aggiungi Commento

Use a spudger to detach the ribbon cable from the circuit board. Lift the black clip up to unlock it as before.
  • Use a spudger to detach the ribbon cable from the circuit board. Lift the black clip up to unlock it as before.

Aggiungi Commento

Remove the 3 screws holding the lens assembly in place.
  • Remove the 3 screws holding the lens assembly in place.

    • The two screws on the left are 4.5mm with washers.

    • The single screw on the right is 4mm.

Aggiungi Commento

Push the lens assembly slightly toward the circuit board, and pull the left side out of the casing first. You will have to wiggle this out gently.
  • Push the lens assembly slightly toward the circuit board, and pull the left side out of the casing first. You will have to wiggle this out gently.

Aggiungi Commento

Remove the entire assembly out of the casing. The ribbons on the left and bottom of the assembly simply rest on the camera housing.
  • Remove the entire assembly out of the casing.

    • The ribbons on the left and bottom of the assembly simply rest on the camera housing.

Aggiungi Commento

Use the spudger to unclip the top ribbon cable from the circuit board.
  • Use the spudger to unclip the top ribbon cable from the circuit board.

Aggiungi Commento

Remove the single 2mm screw in the bottom right corner of the circuit board
  • Remove the single 2mm screw in the bottom right corner of the circuit board

Aggiungi Commento

Gently slide the circuit board out away from the port connections. Pull it toward where the lens used to be. Some wiggling may be necessary to remove. The circuit board is fitted into slots attached to the side of the camera. Do not angle upwards to remove.
  • Gently slide the circuit board out away from the port connections. Pull it toward where the lens used to be. Some wiggling may be necessary to remove.

    • The circuit board is fitted into slots attached to the side of the camera. Do not angle upwards to remove.

Aggiungi Commento

Take note of how the slots fit into the circuit board for easy replacement.
  • Take note of how the slots fit into the circuit board for easy replacement.

Aggiungi Commento

After removing the AV circuit board you are left with the front casing attached to the inner casing and flash unit.
  • After removing the AV circuit board you are left with the front casing attached to the inner casing and flash unit.

  • First you must remove two 3.5mm blue screws near the hole of the lens that attach the inner casing.

Aggiungi Commento

Remove the 3.5mm colorless screw that lays within the square opening of the inner casing.
  • Remove the 3.5mm colorless screw that lays within the square opening of the inner casing.

Aggiungi Commento

Remove the front casing from the rest of the device.
  • Remove the front casing from the rest of the device.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Kevin Lufkin

Membro da: 11/10/2010

155 Reputazione

2 Guide realizzate

Team

Cal Poly, Team 9-21, Regan Fall 2010 Membro di Cal Poly, Team 9-21, Regan Fall 2010

CPSU-REGAN-F10S9G21

4 Membri

7 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 6

Tutti i Tempi: 7,090