Introduzione

This guide will show you how to remove the top panel buttons so you can install new ones.

Parti

Nessuna parte richiesta.

Move the switch on the battery door to the Open position.
  • Move the switch on the battery door to the Open position.

  • The door will automatically swing open after you let it go.

Aggiungi Commento

Push the small gray tab on the top right corner to the left. The battery will pop out slightly. Keep your finger clear of the battery when it pops out.
  • Push the small gray tab on the top right corner to the left. The battery will pop out slightly.

  • Keep your finger clear of the battery when it pops out.

Aggiungi Commento

Push the memory card in and let go.
  • Push the memory card in and let go.

  • The memory card will pop out slightly.

  • Pull out the memory card.

Aggiungi Commento

Unscrew the small screws on the sides of the camera. The screws on the left side(#00P, 4.7mm) are longer than the screw on the right side(#00P, 3.3mm).
  • Unscrew the small screws on the sides of the camera.

  • The screws on the left side(#00P, 4.7mm) are longer than the screw on the right side(#00P, 3.3mm).

Aggiungi Commento

Kit RAM Mac
Accelera il Mac. Porta la memoria al massimo.
Kit RAM Mac
Metti più memoria nel tuo Mac.
Unscrew the three small screws on the bottom(#00P, 3.3mm). The bottom will fall off.
  • Unscrew the three small screws on the bottom(#00P, 3.3mm).

  • The bottom will fall off.

Aggiungi Commento

Lift up the bottom back cover by prying the bottom edge with the spudger. Gently lift up the back cover with your hand from the bottom to the top. Gently lift up the back cover with your hand from the bottom to the top.
  • Lift up the bottom back cover by prying the bottom edge with the spudger.

  • Gently lift up the back cover with your hand from the bottom to the top.

Aggiungi Commento

Lift the tabs on the ZIF connectors. The ribbon cables should easily come out of the ZIF connectors. The ribbon cables should easily come out of the ZIF connectors.
  • Lift the tabs on the ZIF connectors.

  • The ribbon cables should easily come out of the ZIF connectors.

Aggiungi Commento

Using the spudger, pry off the top cover by gliding the spudger along the entire edge between the top cover and the front cover. Be careful not to damage the cylindrical capacitor on the circuit board under the top cover.
  • Using the spudger, pry off the top cover by gliding the spudger along the entire edge between the top cover and the front cover.

  • Be careful not to damage the cylindrical capacitor on the circuit board under the top cover.

Aggiungi Commento

Unscrew the small screws beneath the top cover(#00P, 1.7mm).
  • Unscrew the small screws beneath the top cover(#00P, 1.7mm).

Aggiungi Commento

Lift the motherboard out with your hand by pushing the tabs out and pulling the motherboard up. The on/off switch and the anti-shake button may fall out. The on/off switch and the anti-shake button may fall out.
  • Lift the motherboard out with your hand by pushing the tabs out and pulling the motherboard up.

  • The on/off switch and the anti-shake button may fall out.

Aggiungi Commento

The buttons are hardwired into the top motherboard board.
  • The buttons are hardwired into the top motherboard board.

  • To replace the top buttons, you must replace the top motherboard.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Karissa

Membro da: 13/04/2012

50 Reputazione

8 Guide realizzate

Team

Cal Poly, Team 6-23, Amido Spring 2012 Membro di Cal Poly, Team 6-23, Amido Spring 2012

CPSU-AMIDO-S12S6G23

4 Membri

10 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 2

Tutti i Tempi: 496