Introduzione

This guide show you how to remove and replace the Palm Centro's speakers

Parti

Nessuna parte richiesta.

Press and slide open the battery cover. Press and slide open the battery cover.
  • Press and slide open the battery cover.

Aggiungi Commento

Caution: Turn cell phone off before removing battery!
  • Caution: Turn cell phone off before removing battery!

  • Press battery to the right.

  • Then lift up battery pack to remove.

Aggiungi Commento

Phone with battery removed
  • Phone with battery removed

Aggiungi Commento

Remove the touchpad pen from the top left corner on the back to reveal the last of 6 screws to be removed.
  • Remove the touchpad pen from the top left corner on the back to reveal the last of 6 screws to be removed.

Aggiungi Commento

Lift the rubber cap at the top right to reveal the sixth screw.
    • Lift the rubber cap at the top right to reveal the sixth screw.

    • Caution: There is a small Palm sticker under the rubber cap. Tampering with or removing this sticker will void your warranty!

    • Remove the six screws using the T5 Torx screwdriver.

Aggiungi Commento

Remove the SIM card so housing can be separated. Remove the SIM card so housing can be separated.
  • Remove the SIM card so housing can be separated.

Aggiungi Commento

Use a plastic pry tool to separate the bottom of the case to remove the small plastic insert. Use a plastic pry tool to separate the bottom of the case to remove the small plastic insert.
  • Use a plastic pry tool to separate the bottom of the case to remove the small plastic insert.

Aggiungi Commento

Remove the small plastic insert at the bottom of the phone. Remove the small plastic insert at the bottom of the phone.
  • Remove the small plastic insert at the bottom of the phone.

Aggiungi Commento

Continue with plastic pry tool all the way around the phone to remove the back housing. Continue with plastic pry tool all the way around the phone to remove the back housing.
  • Continue with plastic pry tool all the way around the phone to remove the back housing.

Aggiungi Commento

Carefully peel back the tape holding the speaker (left) and keyboard (right) connection tabs in place.
  • Carefully peel back the tape holding the speaker (left) and keyboard (right) connection tabs in place.

Aggiungi Commento

Using the plastic prying tool, lift the tabs and carefully pull the contact connections out on both sides.
  • Using the plastic prying tool, lift the tabs and carefully pull the contact connections out on both sides.

    • Be very careful, these electronics are delicate!

Aggiungi Commento

Separate the logic board from the case by lifting and pulling out the bottom.
  • Separate the logic board from the case by lifting and pulling out the bottom.

Aggiungi Commento

Pry the four plastic latches free that connect the antenna to the logic board. Excessive force may damage your logic board! Remove the antenna from the logic board.
  • Pry the four plastic latches free that connect the antenna to the logic board.

    • Excessive force may damage your logic board!

  • Remove the antenna from the logic board.

Aggiungi Commento

The internal speaker is attached to the antenna. To remove it, pry the speaker from the antenna using the tip of your screwdriver.
  • The internal speaker is attached to the antenna. To remove it, pry the speaker from the antenna using the tip of your screwdriver.

    • The speaker should be placed back into its spot in the correct position. Take notice of the gold connectors

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Kevin

Membro da: 12/04/2010

31 Reputazione

2 Guide realizzate

Team

Cal Poly, Team 15-49, Garner Spring 2010 Membro di Cal Poly, Team 15-49, Garner Spring 2010

CPSU-GARNER-S10S15G49

5 Membri

12 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 2

Tutti i Tempi: 1,393