Introduzione

You need a T5 screwdriver to remove the screws.

Parti

Nessuna parte richiesta.

In order to remove the back cover, you must press the indicated button.
  • In order to remove the back cover, you must press the indicated button.

Aggiungi Commento

With the button pressed, apply light pressure and slide the back cover off. This will allow you to access the battery
  • With the button pressed, apply light pressure and slide the back cover off.

  • This will allow you to access the battery

Aggiungi Commento

In order to remove the battery, pull it out from the same side that the rubber button is on.
  • In order to remove the battery, pull it out from the same side that the rubber button is on.

Aggiungi Commento

Using a plastic opening tool, separate the back cover from the phone. Using a plastic opening tool, separate the back cover from the phone. Using a plastic opening tool, separate the back cover from the phone.
  • Using a plastic opening tool, separate the back cover from the phone.

Aggiungi Commento

Continue along the edge with the plastic opening tool. Continue along the edge with the plastic opening tool.
  • Continue along the edge with the plastic opening tool.

Aggiungi Commento

Gently, remove the back cover. Gently, remove the back cover. Gently, remove the back cover.
  • Gently, remove the back cover.

Aggiungi Commento

Unscrew the indicated screws using the T5 screwdriver. Unscrew the indicated screws using the T5 screwdriver. Unscrew the indicated screws using the T5 screwdriver.
  • Unscrew the indicated screws using the T5 screwdriver.

Aggiungi Commento

Open the phone up and use the plastic opening tool to remove the cover to the keyboard. Be careful not to break the plastic during this step; do your best not to force anything.
  • Open the phone up and use the plastic opening tool to remove the cover to the keyboard.

  • Be careful not to break the plastic during this step; do your best not to force anything.

Aggiungi Commento

The button board will be loose once the cover is removed. Lift it up to reveal the sensor board.
  • The button board will be loose once the cover is removed.

  • Lift it up to reveal the sensor board.

Aggiungi Commento

With the T5 Screwdriver, remove the marked screws. With the T5 Screwdriver, remove the marked screws.
  • With the T5 Screwdriver, remove the marked screws.

Aggiungi Commento

With the screws removed, the sensor board should be free to flip up. With the screws removed, the sensor board should be free to flip up.
  • With the screws removed, the sensor board should be free to flip up.

Aggiungi Commento

Disconnect the wire with the plastic opening tool. Disconnect the wire with the plastic opening tool.
  • Disconnect the wire with the plastic opening tool.

Aggiungi Commento

Remove the screws marked. The Screw on the left is located underneath the cable. With those screws removed, the circuit board and sensor board will be detached from the rest of the phone.
  • Remove the screws marked.

  • The Screw on the left is located underneath the cable.

  • With those screws removed, the circuit board and sensor board will be detached from the rest of the phone.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 3 persone hanno completato questa guida.

Team

Cal Poly, Team 18-21, Garner Spring 2011 Membro di Cal Poly, Team 18-21, Garner Spring 2011

CPSU-GARNER-S11S18G21

4 Membri

7 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 11

Ultimi 30 Giorni: 36

Tutti i Tempi: 5,293